Meraki

MarcP · ‎Apr 19 2022

Hi all, recently I added an SSID with iPSK, for testing. After testing and recognizing it does not fit my requirements, it got deleted. Deleted the GP´s as well and so on. Since then, all clients in the clients-overview are shown with "custom"-policy. Looking into the clients details page it shows following (only Wifi Client): How do I get rid of this? Is it a bug? Regards Marc

MarcP · ‎Apr 19 2022

Recommend to check your firewall, Camera settings and to verify all switches/uplinks which are involved know this vlan (maybe it is new?)

MarcP · ‎Apr 19 2022

I would also recommend a 1Gb SFP module as well. And would add to be aware, this is not a Meraki SFP you are using. Maybe this can cause these crc errors as well.

MarcP · ‎Apr 18 2022

We use 4 SSIDs everywhere... And on some APs even 5 SSIDs. So far, no problems. And got a good amount of devices within the locations/networks.

MarcP · ‎Apr 14 2022

Did it work?

MarcP · ‎Apr 14 2022

Haven´t done this yet, so I´m not sure. Would imagine it may interrupt for a short period of time, but someone else can probably give you more verified information. Do you maybe have a testlab where you can figure this out? BTW, understood it like you want to bind it to the old template again, which seem to cause in a problem.

MarcP · ‎Apr 14 2022

You may face a problem: https://documentation.meraki.com/General_Administration/Templates_and_Config_Sync/Managing_Multiple_Networks_with_Configuration_Templates

MarcP · ‎Apr 14 2022

Isn´t this a restriction you make on your exchange? From where it is possible?

MarcP · ‎Apr 13 2022

sounds like an IP address from another region / location was taken? That would of course explain why it didn't work. Since the subnet was not known. Then, as mentioned, the device makes a fallback to the old - working - address. However, great it got solved.

MarcP · ‎Apr 13 2022

Does something need to be forwarded on your L3 switch? Any firewall in between, you forgot? Any multicast/IGMP snooping settings missing?

MarcP · ‎Apr 13 2022

This post is regarding to AirPrint, but could be a good hint: IGMP snooping - https://www.reddit.com/r/meraki/comments/icx2sz/bonjour_forwarding_and_airprint_printer/ And in addition to the reddit threat, this link is mentioned in the discussion: https://community.meraki.com/t5/Switching/Multicast-Basic-s/td-p/25706

MarcP · ‎Apr 13 2022

Any news? actually I´m interessted 😄

MarcP · ‎Apr 12 2022

It is the same with MR-74, tested it (need to use them temporary indoor, firstly I just put it on a table) vertically is much better than horizontally, I can confirm this. surely it is regarding to the MA-ANT-20 design.

MarcP · ‎Apr 12 2022

Yeah, thanks a lot for this contest 🙂 Congratulations to all, specially to rbnielsen

MarcP · ‎Apr 12 2022

Have you check if the IP you chose for the switch as future static IP is not already in use? Have you veryfied the new static IP is allowed to reach the internet on the necessary ports?

MarcP · ‎Apr 12 2022

I do not understand this: "You cannot route traffic from other networks through a single network's tunnel in a 3rd party VPN" If you have Org A and Org B and all or all necessary subnets in this VPN-Tunnel, the systems build all IPSec-SA´s on their own. no one needs to set up seperated IPSec Tunnels for each remote network. Which I think is not possible to do several Tunnels between the same public IPs

MarcP · ‎Apr 12 2022

did you verify @PhilipDAth comment?

MarcP · ‎Apr 12 2022

Need to add/ correct @Brash (sorry), WLC must not be directly in this network. You can forward the Cisco APs packets over VPN to the WLC. "IP helper address" are the keywords 😉

MarcP · ‎Apr 12 2022

You have two Orgs connected with VPN to each other and want to use resources like DNS from Org A in org B, correct? If you used Site-toSite-VPN you configure the remote site subnets and there has to be the subnets which are necessary. Afterwards the DNS server is reachable from the remote site. Keep in mind you may have to allow this communication in a third party firewall if you have one.

MarcP · ‎Apr 12 2022

unfortunatelly, as mentioned, we don´t use auto-vpn and never used it before, sry.

MarcP · ‎Apr 12 2022

You may want to have a look at these, we don´t have auto-vpn in use...: https://community.meraki.com/t5/Security-SD-WAN/Route-Table-Routes-learned-on-AutoVPN-Keeping-spinning-under/td-p/132506 https://documentation.meraki.com/MX/Site-to-site_VPN/Meraki_Auto_VPN_-_Configuration_and_Troubleshooting https://www.reddit.com/r/meraki/comments/agpa5t/route_table_status_spinning_vs_green_vpn_routes/?sort=old

MarcP · ‎Apr 12 2022

So its WPA2 enterprise - do you see the request on the radius server, in the event log? Meraki log looks like radus is not responding. Was the WPA2 Enterprise ever working?

MarcP · ‎Apr 12 2022

@Gislavedshus all went well?

MarcP · ‎Apr 11 2022

We have these switches, too. Another argument: 10GBit Uplinks are used to connect to the coreswitches, in an AGGR to get 20GBit Uplink to cores and of course redundance.

MarcP · ‎Apr 11 2022

You can connect them, and use PoE if you have it at your Switch, sure. But you will still need a WLC from Cisco classic to configure it.

About MarcP

MarcP

Community Record

Badges