Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About mcoomber
mcoomber
Here to help
Member since Sep 21, 2021
a month ago
Community Record
13
Posts
1
Kudos
0
Solutions
Badges
Mar 22 2024
6:39 AM
Thanks very much for the support and guidance. Will revert to you tomorrow after configuration.
... View more
Mar 22 2024
6:25 AM
I just want to configure the present configuration in the router to the MX 84. So I want to know what configs in the router I need and which I can skip. Also which config Meraki corresponds with the config on the router. Thanks.
... View more
Mar 22 2024
6:00 AM
I have configured interface GigabitEthernet0/1 on the router to Port 2 on Meraki and interface GigabitEthernet0/2 on the router to Port 1 on the Meraki. Without configuring NAT, do I need to configure the static routes and ACL? If so where in the Meraki do I do these configurations Thanks for the support thus far.
... View more
Mar 18 2024
6:59 AM
I've got a Cisco 1921 Series router and an SDWAN within my network. The link from the service provider connects to the 1921 Series router and the router connects the SDWAN. I want to take the 1921 router off the network. Before doing so I want Can the configuration in the router be configured in the SDWAN Below is the configuration from the router. How can this be translated to the routing config in the SDWAN. The aim to have the connection from the ISP directly connected to the SDWAN since its already configured as the default gateway and Firewall. Thanks x.x.x.x 255.255.255.248 interface GigabitEthernet0/1 ip address x.x.x.x 255.255.255.248 ip nat outside ip virtual-reassembly in duplex auto speed auto ! interface GigabitEthernet0/2 ip address x.x.x.x 255.255.255.252 ip nat outside ip virtual-reassembly in duplex auto speed auto ! ip tftp source-interface GigabitEthernet0/0.5 ip nat pool Pool-NAT-ISP1 x.x.x.x x.x.x.x netmask 255.255.255.252 ip nat pool Pool-NAT-ISP2 x.x.x.x x.x.x.x netmask 255.255.255.252 ip nat source static x.x.x.x x.x.x.x ip nat inside source route-map ISP1 pool Pool-NAT-ISP1 overload ip nat inside source route-map ISP2 pool Pool-NAT-ISP2 overload ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1 x.x.x.x track 1 ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/2 x.x.x.x track 2 ! ip access-list extended Internet permit ip 172.16.0.0 0.0.1.255 any permit ip 192.168.20.0 0.0.0.255 any ip access-list extended RTR-SIP-REG permit ip host 172.20.0.2 any ! ! nls resp-timeout 1 cpd cr-id 1 route-map ISP2 permit 10 match ip address Internet match interface GigabitEthernet0/2 ! route-map ISP1 permit 10 match ip address Internet match interface GigabitEthernet0/1 ! no ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1 x.x.x.x x.x.x.x track 1 ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1 x.x.x.x track 1 no ip nat inside source route-map ISP1 pool Pool-NAT-ISP1 overload no ip nat pool Pool-NAT-ISP1 x.x.x.x x.x.x.x netmask 255.255.255.252 ip nat pool Pool-NAT-ISP1 x.x.x.x x.x.x.x netmask 255.255.255.248 ip nat inside source route-map ISP1 pool Pool-NAT-ISP1 overload
... View more
Apr 13 2023
9:36 AM
Hi, I'm using TeamViewer Asset Management for remote management of my devices. This app has a patch management and software deployment . So today, I was updating the devices that it had flagged as needing updates and Security Patches. While doing this, Meraki blocked all update packages that were in *.zip and flagged them as malicious. A total of 84 files were blocked according to the Dashboard. However, when i downloaded the same files from the Vendors update site, these files are not flagged. Might this be a False Positive? Thanks.
... View more
Labels:
- Labels:
-
Other
Feb 6 2023
4:26 AM
Hi All, My Meraki dashboard reports that Google Services is utilizing on average 60% of the bandwidth alone. I want to do traffic shaping of this service but do not know the expression to use to limit its usage or do scheduling when it should run. Help needed. Thanks
... View more
Mar 8 2022
3:30 AM
1 Kudo
Hi All, 1. Is it possible to configure the MX84 with two different WAN Links from different service providers? 2. If No.1 is possible. Can the traffic be shaped such that particular traffic uses a particular link and other traffic uses another link? E.g. All videos and social Media goes through Provider X and all Productivity goes through Provider Y. If both are possible, can you please show how such is configured. Thanks
... View more
Labels:
- Labels:
-
ACLs
Oct 28 2021
11:15 AM
It is from the ISP device that I am responding to your suggestions.
... View more
Oct 28 2021
11:07 AM
I am the IT guy. It's an old Z1 that was in use. Only the amber flash link light is on. I can't get access to the Internet and yes it is connected to the existing ISP router.
... View more
Oct 28 2021
4:25 AM
My Z1 Teleworker doesn't change state from steady amber at boot up. Anything I can do with it or is it toasted? Thanks
... View more
Labels:
- Labels:
-
Other
Sep 23 2021
3:18 AM
Hi, Thanks for your response. Yes, my DC is also a DNS Server for my clients. Your answer gives me some relief.
... View more
Sep 21 2021
9:17 AM
Hi, The MX Events constantly gives me the IDS Alerts: INDICATOR COMPROMISE: Suspicious .top dns query event. Whats worrying is that the source is from my Domain Controller and the destination is to dns.google. I've also got an android device which I am yet to identify since it appears with its mac address having the same alert. Added to that, today, I have seen an event from an external IP Address source to a device within my network with a SERVER-WEBAPP: PHPUnit PHP remote code execution attempt and a GPON Router authentication bypass and command injection attempt. Any help is welcome. Thanks
... View more
Labels:
- Labels:
-
Other
© 2024 Cisco Systems, Inc.
