Hi   I have two meraki MX-450 and it is working in HA and in concentratot mode.   At the same time Pair of MXs are working in VRRP and using virtual uplink IP's (Shared IP) to send traffic to Internet.   We are using NAT for MX subnet IP and have full internet access.   Connectiivty Details: SW-10.155.0.x/20--Te1/0/16--> MX-450 Primary IP:10.155.0.a/20 SW-10.155.0.y/20--Te1/8--> MX-450 spare IP:10.155.0.b/20   SW-10.155.0.x/20 and SW-10.155.0.y/20 have trunk/TAG connectivity(SW-10.155.0.x/20-->Te1/0/19--Te3/2->SW-10.155.0.y/20.   We have checked there is no ping drop between between MX's IP's. and Firmware is also upto date.   Now the issue is we are getting masive logs of VRRP transaction(Backup and master) on event logs as well as VRRP MAC flap on Network SWITCH betwen Ports ((SW-10.155.0.x/20 on Port Te1/0/19 and Te1/0/16).I have attached Topoloy for better understanding.I apprciate your feedback to mitigate this issue.       ... View more

Hi,   I am using two products MR70 and MR46 for end users. Whenever I check internet speed via speedtest.net remaining connected on MR 46, I am getting Excellent upload/download speed(200 Mpbs plus on both).     But When i connect over MR70 i get just 50 to 60 Mpbs Upload/download speed.   ISP is same and having sufficient Bandwidth and utilizes not more than 20 to 30 percent of total bandwidth.   I have tested internet link with various client but results always remain same.   I thought there might be some issue with Local LAN/cable where MR70 is connected so for further troubleshooting i just interchanged one of the MR46 with MR70 and connected with same Ethernet SW and same cable but there is no any improvement in speed . The internet speed always getting lower in respect of MR46.   Any further suggestion would be highly appreciated ... View more

Hi , Need support to find solution for Cisco Meraki Manage Wifi which has a constrain of adding MAC address for  MAC base authentication (only 3000 Mac Address support). Now clients are increasing and looking for solution to enhance the MAC whitlisting capapcity. Please suggest what devices/settings are required for same. ... View more

Hi Team,   Last few days i am getting client connectivity issue and delay in client connectivity to meraki AP. User connectivity is through Radius server. I have added Meraki AP on Radius server still some users getting error of  "Failed connection to SSID XXX on AP XXX during authentication because the auth server did not respond" and Meraki reason code is "RADIUS timeout". however not all users are having same issue on same Access point. I am not getting how few clients are working while few are facing error. ... View more

I am using Sponsored guest login for Guest users. My question is can we modify in Splash page so that Guest users request can be redirected to Individual Sponsors Email instead of domain. ... View more

Hi Team,   I have to block some specific IP facing Internet. I am confused in term Layer3 Firewall Rule available on MX firewall as well As on Wireless Option. I have MX firewall and MR AP are deployed under it also I have BSSID scenario.     Mx Firewall-->Firewall--> Layer 3 Rule Wireless-->Firewall and traffic Shaping--> Layer 3 Rule   ---IF i apply any rule on MX firewall under layer 3 rule then will it be also applicable for clients ( Wireless-Firewall Layer 3) or ---If I block anything on MX , will it block for everyone.   ... View more

There are multiple AP's deployed in my environment and using Ip v4 addressing. we are not using IPv6 as of now but there is one AP which has taken Ipv6 address and it is in auto mode. Can we disable auto mode as I don't want this AP to obtain v6 address.     ... View more