Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
- About ranjankumarsgh
ranjankumarsgh
Getting noticed
Member since Aug 3, 2021
12-12-2022
Community Record
25
Posts
2
Kudos
2
Solutions
Badges
12-07-2022
08:33 PM
I tried to remove from network multiple times but all went invain. I will try factory reset
... View more
12-07-2022
08:32 PM
Hi DHCP is working as other clients in same vlan are getting IP and even Mr76 is also getting IP from vlan 119.
... View more
12-07-2022
08:30 PM
Yes wired client are getting IP even MR 76 is also getting IP from vlan 119
... View more
12-07-2022
09:02 AM
Hi Ryan, Thanks for your comment. There is no such config on switchport. The below are the switchport config and the native vlan is defualt vlan 1. On Dashboard, MR 76 AP LAN IP is set DHCP and Vlan "No any vlan/blank" Note : The AP mode is showing in repeater but there is no any other meraki AP in that area. The repeater mode might be due to not reachable from dashboard. interface GigabitEthernet0/7 switchport access vlan 119 switchport mode access Your further inputs will be highly appreciated.
... View more
12-07-2022
06:01 AM
Hi Please help me to resolve the MR76 AP issue as it is not showing any LAN IP on dashboard. Mr76 is connected with Local cisco switch and we are running own DHCP server in our network. MAC is learning on local SW Port and also dynamic IP is getting allotted as per ARP table. Also local Meraki page of MR76 is showing " AP is connected to internet and meraki cloud. I have tried to assign static IP on AP but still it is not getting fully Lived(Repeater symbol) on dashboard and no LAN IP is showing. More Interesting is that i have local Cisco switch and cdp is enabled on it but mr76 ap is not showing on cdp neighbor. Once i reboot the ap then it shows in cdp neighbor for few minutes and then vanishes. As per meraki TAC, it is local dhcp issue. But I am not getting any clue that it is due to dhcp as IP is allotted to AP and it is reachable over lan also. Please suggest further investigation on it.
... View more
Labels:
- Labels:
-
Other
04-14-2022
10:36 PM
Hi , Need support to find solution for Cisco Meraki Manage Wifi which has a constrain of adding MAC address for MAC base authentication (only 3000 Mac Address support). Now clients are increasing and looking for solution to enhance the MAC whitlisting capapcity. Please suggest what devices/settings are required for same.
... View more
Labels:
- Labels:
-
Other
04-13-2022
07:35 PM
Hi, I am interested to know how can i set alert on dashboard so that i can get email notification for any specific client about its connection and disconnection from network. Please help it's there in dashboard.
... View more
Labels:
- Labels:
-
Other
02-16-2022
02:35 AM
Hi Team, Last few days i am getting client connectivity issue and delay in client connectivity to meraki AP. User connectivity is through Radius server. I have added Meraki AP on Radius server still some users getting error of " Failed connection to SSID XXX on AP XXX during authentication because the auth server did not respond" and Meraki reason code is "RADIUS timeout". however not all users are having same issue on same Access point. I am not getting how few clients are working while few are facing error.
... View more
10-11-2021
05:30 AM
I am using Sponsored guest login for Guest users. My question is can we modify in Splash page so that Guest users request can be redirected to Individual Sponsors Email instead of domain.
... View more
10-10-2021
09:34 PM
Thanks for clarification. Can we apply Layer 3 rule with Multiple Source IP and Multiple Destination Ip's together in single rule instead of single rule for each source and destination. I am not sure whether Comma between IP's will work. Please let me know the given example as below is correct format for Layer 3 creation with multiple destination Ip's. E, G Source Port : Any Source IP: ANY Destination IP: X.x.x.x, Y.y.y.y, Z.z.z.z, A.a.a.a. Destination Port : any
... View more
10-06-2021
03:29 AM
Hi Team, I have to block some specific IP facing Internet. I am confused in term Layer3 Firewall Rule available on MX firewall as well As on Wireless Option. I have MX firewall and MR AP are deployed under it also I have BSSID scenario. Mx Firewall-->Firewall--> Layer 3 Rule Wireless-->Firewall and traffic Shaping--> Layer 3 Rule ---IF i apply any rule on MX firewall under layer 3 rule then will it be also applicable for clients ( Wireless-Firewall Layer 3) or ---If I block anything on MX , will it block for everyone.
... View more
10-06-2021
03:18 AM
2 Kudos
Hi, Thanks for your reply. It is not like wild card. I have cross checked with TAC and we cannot block URL/IP based on hash value
... View more
10-06-2021
12:59 AM
I have URL and IP as well as HASH value of URL. I can Block based on IP/URL but i need to block HASH value against URL. I am looking how can we block this through Firewall Layer3 Rule or any other Options available in meraki.
... View more
10-06-2021
12:32 AM
Hi, Can you please let me know how can can we block hash value in Firewall Rule instead of IP's on MX firewall 450
... View more
09-23-2021
04:24 AM
There are multiple AP's deployed in my environment and using Ip v4 addressing. we are not using IPv6 as of now but there is one AP which has taken Ipv6 address and it is in auto mode. Can we disable auto mode as I don't want this AP to obtain v6 address.
... View more
09-23-2021
01:11 AM
1 6 & 11 are not overlapping channel. Apart from this can we use other channel
... View more
09-23-2021
12:55 AM
End devices are not capable to support 5ghz. I will have to stabilize with 2.4 Ghz only. Few more Merkai AP's are deployed at location and configured in auto channel selection .
... View more
09-19-2021
01:15 AM
I am facing high channel utilization on Ch11 (approx 67% to 71%) as well these utilization are showing on rest of channels also on 2.4 Ghz band. Is there any way to mitigate this. Also I checked interferance on Channel 11 as per below output. Please let me understand what does it mean "not Seen" on LAN Column
... View more
Labels:
- Labels:
-
Interference
09-17-2021
03:23 AM
Thanks I got your Point
... View more
09-17-2021
03:09 AM
Hi Thanks for understanding. I could not pull data from Link https://developer.cisco.com/meraki/api-v1/#!get-organization-devices-statuses. I have downloaded CSV file from dashboard including Contacted at column and below value is coming. what does it mean assuming all are in Seconds and then converted into days. it is not expected to be up as per converted Days. Contacted at 1631872018 1631871977 1631871994 1631871983
... View more
09-13-2021
02:47 AM
Thanks for your reply. Once I download data in CSV file , the value of contacted at is coming in Numeric and i am not getting it that it is milliseconds/microseconds. My requirement is to collect all AP details last contacted with dashboard
... View more
09-13-2021
01:56 AM
Hi Team, Please help me to understand about two points on dashboard column ( Dashboard-->Wireless-->Access point) Usage and contacted at. I have filtered the dashboard column for access point for usage and contacted at. Please clarify about below things --Usage: Data usage is showing against each access point please let me the period of collected data --Contacted at: Each access points showing time value in this column. Please let me how AP calculate time value at contact at column.
... View more
08-25-2021
10:11 AM
Hi Team, Can anyone respond me for below query. is it possible to pull the report of such MR access point which has less utilized or minimal users connected in last 30 days.
... View more
Labels:
- Labels:
-
Other
08-18-2021
05:38 AM
Thanks for your clarification.
... View more
08-18-2021
04:14 AM
Hi , We have own third party NMS tool deployed in LAN for Monitoring and reporting Meraki Devices through SNMP Pooling. Now We want to enable API on Meraki dashboard and need to Monitor and capture reports in our NMS tool. Please help me for below query. Considering API is Enabled on Dashboard. 1.What are the API details need to be handy to configure API setting in our NMS tool 2.Can we have Read/Write access on meraki devices from NMS tool. 3.is internet required on NMS tool to access Meraki API.
... View more
Labels:
- Labels:
-
Dashboard API
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 324 | 12-07-2022 08:33 PM | |
| 693 | 08-18-2021 05:38 AM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 2 | 863 |
