Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About Mike05
Community Record
20
Posts
1
Kudos
0
Solutions
Badges
I just noticed also that Meraki login page is new, not sure when the update came in. I hope it didn't add up to the missing aggregation configuration that I made during the time I'm configuring the switches 😄
... View more
Hi @GIdenJoe , @Brash , @MartinLL , Thank you very much for all your inputs in this case. I managed to resolve the problem. Basically, most of the "aggregation" that I configured in Meraki Dashboard isn't there when I checked the settings yesterday. It's just weird that the first switch that I successfully tested for link aggregation also encountered issue hours after it has been established. Since I have less experience with Meraki, I tend to have a test first before proceeding with other equipment. In the end I re-configured most of the Meraki switches for aggregation and from there LACP worked well. Regards, Mike
... View more
Hi @MartinLL , Thank you for the response. This is the exact procedure that we made. Have the MS connect to internet using port 52 then configure 49-50 as aggregate. Wait for around 30 mins, then change the connection by removing port 52 and use 49-50. During the first few minutes I can see that it's properly working but when I added and connected other IDF switches with the same settings going to C9300X, I noticed that 1 of the port gets suspended. When I tried to do "shut / no shut" from C9300X port-channels that is previously working, 1 of the port also got suspended. Currently, MSs can connect to internet using aggregation link 49 but with 1 port (50) suspended in C9300X. Regards, Mike
... View more
Hi @Brash , Thank you for the response. I'm pretty sure that it is cabled and configured correctly. That's why I'm scratching my head on this issue 😞 Maybe I can try some debugs on C9300X tomorrow when I'm onsite.
... View more
Jan 28 2024
7:39 PM
Hi Experts, Do you have any idea why 1 port of C9300X gets suspended when configured using LACP protocol? In MS210-48, I just bundled port 49 and 50 wherein I confirmed that AGGR/0 is created. Configuration of C9300X is pretty basic. int range twe 1/0/1, twe 2/0/1 switchport mode trunk channel-group 101 mode active ! int port-channel 101 switchport mode trunk ! Is there someone with the same concern? TIA. Mike
... View more
Jan 19 2024
12:19 AM
1 Kudo
Hi @Purroy , This is noted. Thank you for your time for explaining about this inquiry. Regards, Mike
... View more
Jan 18 2024
11:24 PM
Hi @DarrenOC , Thank you for the response. The APs(MR46) are brand new so it's not yet registered in the Dashboard. So I'm wondering if it's possible. Regards, Mike
... View more
Jan 18 2024
7:21 PM
Hi to all, Just want to ask if it's possible to access Meraki AP local status page via wired? I'm using poe injector so that I can connect directly using a laptop but currently unable to access. Tried to statically assign IP in my laptop and access 10.128.128.126 and 10.128.128.128 but not working. For now I can only access it via wireless by connecting to broadcasted "meraki-scanning". Regards, Mike
... View more
Jan 18 2024
4:56 PM
Hi @FeliA , Thank you for the explanation. I kind of get it now. I re-checked Meraki Dashboard and switch number seems irrelevant since you are still going to each switch to configure certain settings. Though you are correct, we can use hostname to re-arrange the position of switches in the dashboard for easier identification in the physical rack. @Brash , Thank you as well for your response yesterday. Regards, Mike
... View more
Jan 17 2024
7:16 PM
Hi @Brash , Thank you for your response. But is there a way to re-order the switches first before provisioning? Regards, Mike
... View more
Jan 17 2024
6:49 PM
Hi everyone, Just want to ask if there is a way to manually assign switch number in a stacking Meraki Switches (say 3 switches)? When I tried it before, there is no settings like this. Regards, Mike
... View more
Jun 26 2023
7:15 PM
Hi Meraki Masters, Just want to ask. If we are going to install 2 MX in HA, is it ok to have only 1 license? TIA
... View more
Dec 5 2021
4:52 PM
Hi @ww , @KarstenI , It works! So that's the way in case I can't access using dedicated management port. Anyway, thanks to all of your replies. Regards, Mike
... View more
Dec 5 2021
4:50 PM
Hi @BlakeRichardson , Thank you for your response. I will explore this option, I'm still new in using Meraki Dashboard 🙂 Regards, Mike
... View more
Dec 5 2021
4:01 AM
Hi @ww , Understood, so meaning I still need to access it based in the original management IP. I'll give it a try when I go onsite tomorrow and give you a feedback. Thanks, Mike
... View more
Dec 5 2021
3:44 AM
Hi @ww , @KarstenI , Thank you for your response. Initially, I added and managed it in the Dashboard so I'm able to change the IP address from there. Its just that during the deployment, I was informed that customer by default has no internet unless you use proxy. I set the IP Address in 172.26.x.x subnet, in this case, should I connect to normal LAN port then access http://172.26.x.x? Regards, Mike
... View more
Dec 5 2021
3:14 AM
Hi Masters, Just want to ask if somebody encountered the issue I am facing with MS125-48 switch. Currently, I can't access the local status page so that I can setup proxy settings. I've tried below. * Laptop set to obtain DHCP. 1. Connect LAN cable to dedicated management at the back of the unit. 2. Check IP address - none (APIPA). 3. Tried to access switch.meraki.com ; my.meraki.com ; setup.meraki.com - all failed. *Laptop set to 1.1.1.99/24 1. Connect LAN cable to dedicated management at the back of the unit. 2. Tried to access 1.1.1.100 - failed 3. Ping 1.1.1.100 - failed. Together with this unit are stacked MS350-24X, the local status page pops up automatically upon connecting to management port so it's just the 3 x MS125-48 that I'm having trouble. Any ideas? TIA, Mike
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 1 | 1237 |
© 2024 Cisco Systems, Inc.
