Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Become a member of the Cisco Meraki Community today
Get answers from our community of experts in record time.
Join nowAbout Snika
Community Record
47
Posts
6
Kudos
1
Solution
Badges
yesterday
2 Kudos
As you suggested, we replaced a large number of APs using Zero Touch Provisioning. It's very simple. I'd like to accept this as the answer, but it seems only one answer can be accepted. Thank you.
... View more
Tuesday
Is the only way to reconfigure all the settings from the old switch on the new one? Is there no better solution?
... View more
Tuesday
This is not the same device. Can I clone the settings from MS120 to MS130? I don't think it's possible.
... View more
Monday
2 Kudos
I want to replace the device from MS120 to MS130. I've checked a few methods. 1. Switch clone 2. “Replace” from inventory I'm not entirely sure, but it seems like the above two methods only work between identical devices. I want to keep all settings exactly as they are IP, hostname, location, etc. Any good ideas??
... View more
Monday
MX supports cold swaps. Does MR not support replacement? Do I need to remove the existing MR, connect the new MR, and then manually set the IP, location, hostname? Because the MRs I need to replace number over 1,000.
... View more
Monday
We are currently using an MR Enterprise license. We have purchased an additional MR Enterprise license. Can the CW series use the MR Enterprise license? And what do MR-X and MR-Y mean?
... View more
Monday
We plan to replace the MR with the CW9172. MX provides cold swap guides, and attention must be paid to port mapping. Are there any precautions when replacing the MR series with the CW series?
... View more
Nov 27 2024
6:45 AM
When I did a Radius test, authentication failed on many APs. However, unlike the test results, I can connect wirelessly to all APs in the office. But why does the test fail?
... View more
Labels:
- Labels:
-
SSID
We are using Active directory combined with Splash page. I must use open authentication to use Splash pages. Open authentication does not allow the use of WPA encryption between the PC client and the AP. Is this a security vulnerability? What steps do we need to take to ensure that we meet the requirements of wireless security?
... View more
Labels:
- Labels:
-
SSID
May 7 2024
12:51 AM
MX vpn = A non meraki vpn = B I want to do ipsec vpn tunneling between a A vpn and a B vpn. B vpn is not an ASA. In B VPN setup, the remote subnet is Any and several subnets are routing through the tunnel. As you know, 0.0.0.0 is routed to the WAN. If I route 0.0.0.0 internally as you say, will the internet be possible? Using the ASA as an example, what I want to do is set the Local Subnet to Any on the MX firewall.
... View more
May 2 2024
2:54 AM
For example, let's say have a topology like this. MX is a warm spare. If MX1 goes down, MX2 will become the primary. So the WAN link would be 20.20.20.2? When I am using non meraki vpn and in remote vpn I set vpn peer to 20.20.20.1, If the WAN link changes to 20.20.20.2, the IPSEC VPN tunnel will go down. Can the MX keep the WAN IP of 20.20.20.1 with the warm spare setting so that the tunnel does not go down?
... View more
Labels:
- Labels:
-
3rd Party VPN
-
Firewall
Apr 28 2024
2:24 AM
When set up an IPSEC VPN on the Cisco ASA, you can specify SUBNET as ANY. Is this possible on the MX firewall? I will to set a non-Meraki VPN.
... View more
Labels:
- Labels:
-
Firewall
Apr 21 2024
12:09 AM
It was a C9300, not an MS225. I was mistaken. The MS225 is port-schedulable. The 9300 cannot.
... View more
Apr 19 2024
2:44 AM
The guide says I can assign a port profile from the Swtich port menu. But I can't find the menu.
... View more
Apr 17 2024
3:20 AM
https://documentation.meraki.com/MS/Layer_3_Switching/MS_Warm_Spare_(VRRP)_Overview I've read the VRRP guide. Will VRRP work if I enable warm spare? On non-Meraki products, when configuring VRRP, you need a Real IP and a Virtual IP. In which menu should I set the Real IP and Virtual IP on Meraki?
... View more
Apr 17 2024
2:26 AM
How to create a configuration template? There is currently a Security template for 1 network. I want to add a Switch template. Finally, I want to claim the switch to this network. How do I do that?
... View more
Labels:
- Labels:
-
Other
Mar 26 2024
9:05 PM
I cannot accept multiple answers as a solution. I am sorry for not being able to accept your answer. Thank you for your reply.
... View more
Mar 26 2024
5:27 AM
On the ASA, I had to configure dynamic PAT to use the Internet. Does the MX require PAT settings for the local network to use the Internet?
... View more
Labels:
- Labels:
-
Firewall
Mar 26 2024
4:02 AM
The guide says that the Non-Meraki VPN peers menu is a connection between MXs from different organizations. Can MX do IPSEC VPNs with VPNs from other vendors?
... View more
Labels:
- Labels:
-
3rd Party VPN
-
Auto VPN
-
Firewall
We found and removed WIPS. All issues have been resolved. thank you
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 2215 | Apr 17 2024 2:42 AM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 2 | 82 | |
| 2 | 343 | |
| 2 | 2215 |
© 2026 Cisco Systems, Inc.
