- About FlyingFrames
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
FlyingFrames
Here to help
Member since Aug 16, 2018
4 weeks ago
Community Record
13
Posts
1
Kudos
0
Solutions
Badges
02-25-2020
11:52 AM
Are the following features supported in MR26.7, the current stable release candidate DL-OFDMA**, UL-OFDMA**, TWT support**, BSS Coloring**, UL MU-MIMO** As per data sheets: "** software features can be enabled via firmware updates" @davidvan
... View more
02-18-2020
01:29 PM
Hello, Trying to pitch MR56 however it needs 802.3at but we are looking at 802.3af poe budget. What functionality will we lose, until we get 802.3at? Would they even show up in dashboard! Thanks in advance.
... View more
10-23-2019
02:33 PM
IPSK is documented with ISE & Free RADIUS here: https://documentation.meraki.com/MR/Access_Control/IPSK_with_RADIUS_Authentication Will it also work Meraki Cloud RADIUS?
... View more
09-18-2019
05:01 PM
If the my RADIUS server connectivity is lost from the APs. What is the expected behaviour? It is documented for the cloud Meraki RADIUS server but knobs are given as well. But no such knob exists for my RADIUS server. https://documentation.meraki.com/zGeneral_Administration/Cross-Platform_Content/Behavior_during_Connection_Loss_to_Cisco_Meraki_Cloud#MR.2FWireless_APs_Details I was expecting Meraki APs to cache the credentials and still keep on continuing to authenticate users using either the RADIUS server in the AP or via fallback to cloud RADIUS. Is it possible?
... View more
08-30-2019
11:34 AM
It looks like its 1 stream only in RX. Would this be able to successfully decode 11ax transmissions.
... View more
08-15-2019
10:48 AM
https://fccid.io/UDX-60083010/Test-Report/NII-Test-Report-4121729 Based on the above its a Rx only radio for 2.4 & 5 both. "2.4GHz / 5GHz Scanning (only RX)"
... View more
08-05-2019
02:55 PM
If the 3rd radio is a cheaper 2x2 radio, it might not be able to do its functions of scanning properly! So wanted to know its specs.
... View more
08-05-2019
02:29 PM
The datasheet does not mention the following: Is the 3rd radio for WIDS/WIPS 8x8 or 4x4? Does the 802.11a/n/ac/ax convention apply to it? https://meraki.cisco.com/products/wireless/mr55#tech-specs
... View more
08-05-2019
12:25 PM
1 Kudo
Is it supported to use multiple ports in link aggregation with LACP, for the flexible switch stacking as shown in this example: https://documentation.meraki.com/MS/Stacking/Switch_Stacks#Configuring_a_Flexible_Switch_Stack The document says that ethernet ports can be used but does not mention if they can be multiple in LACP. Kindly help.
... View more
01-25-2019
12:52 PM
Thanks everyone for their detailed inputs & recommendations. However, as per the following link, MR creates an L2 tunnel! 😞 https://documentation.meraki.com/MR/Client_Addressing_and_Bridging/MR_Teleworker_VPN “A Meraki AP at a remote site establishes a layer 2 connection using an IPSec-encrypted UDP tunnel back to the corporate LAN. Tunnels are established on a per SSID basis, and terminate at headquarters on a Meraki MX security appliance. “
... View more
01-24-2019
03:39 PM
We are designing a 1000 site deployment with Z3 as the teleworker solution. There are 1000 sites with one Z3 on each site. As per the documentation, these will be L2 tunnels from MX in the datacenter. If all of them are in one VLAN, can the MX acting as tunnel concentrator, provide some broadcast multicast knobs for controlling that traffic? Or would each site be subject to broadcast from another site?
... View more
08-16-2018
07:05 PM
Employee VLAN currently has more than 500 clients and causing broadcast issues. We are planning to split them into two /24 VLANs say 40 and 50. And then map the employee SSID to a pool of two VLANs. However the UI does not allow to put two VLANs on VLAN ID page of the SSID! How can one achieve that?
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 1 | 401 |
