Meraki

Mr_IT_Guy · ‎Aug 29 2018

Thanks for the shout out @CarolineS. If anything, the thanks should go to @NFL0NR and my boss for the idea to share the photos in the first place. It's been really fun taking pictures with @Maui_Meraki_Dog and all the Meraki swag, though I have to say my wife is the one responsible for the majority of the fashion shoots.

Mr_IT_Guy · ‎Aug 21 2018

@CarolineS, you've made this community a great place to be and be a part of. Thanks for your hard work and due diligence. To all the community members, thanks for all the posts, discussions, pictures, ideas, etc.

Mr_IT_Guy · ‎Aug 21 2018

Mr_IT_Guy · ‎Aug 14 2018

Hi @Philip and welcome to the forums!! Meraki is without a doubt GUI over CLI. In fact, the closest thing you will get to CLI is working with APIs. Meraki is all about "Simplicity" and as you've seen that makes them easier than your typical Cisco router. Many people enjoy that....I personally wish there was a bit more CLI, but oh well. Thanks for the quick answer @AjitKumar!

Mr_IT_Guy · ‎Jul 25 2018

This is FANTASTIC!!! Great to see the Meraki Community grow

Mr_IT_Guy · ‎Jul 2 2018

Congrats to all the MOTMs and thanks for everyone who contributes on a daily basis. Enjoy your vacation @CarolineS!

Mr_IT_Guy · ‎Jun 19 2018

On the same boat. I received my confirmation email congratulating me on my new Switch, but alas no License Key. Like mentioned above, they'll probably get to us.

Mr_IT_Guy · ‎Jun 15 2018

@jdsilva It was great getting to meet you and @Welles and all the other community folks!

Mr_IT_Guy · ‎Jun 13 2018

Hi @OSPF71, If you go to Security Appliance/Teleworker Gateway > Configure > Site-to-Site VPN, there is a section called VPN settings. As long as the vLAN is set to yes in the Use VPN column, then the vLAN will be reachable when using Client VPN. If you wish to change that (i.e you only want VPN to access certain subnets at different MXs across your organization), you will need to add additional rules in Site-to-site outbound firewall at the bottom of the same page. Finally, if you want the client VPN to only access local subnets, set the Use VPN setting to no.

Mr_IT_Guy · ‎Jun 10 2018

I'm in the back left corner by the door

Mr_IT_Guy · ‎Jun 10 2018

And barely made it in time for orientation. Let's do this!

Mr_IT_Guy · ‎Jun 10 2018

Woot! Headed to the airport now! See you there

Mr_IT_Guy · ‎Jun 8 2018

Packing my bag tomorrow! Looking forward to seeing everyone there! @jdsilva, will you be at Orientation/tweet-up events on Sunday?

Mr_IT_Guy · ‎Jun 5 2018

@Adriano that is correct.

Mr_IT_Guy · ‎Jun 5 2018

Hi @Adriano, A template for an MX64 would work on an MX64W. When going through the template setup, you will see that there are options for wireless settings. When applied, a template will apply those settings which pertain to that device. For instance, you can apply a Z1/Z3 to an MX64 template, but the device will not get Content Filtering settings because content filtering is not available on the device. Additionally, the Z1/Z3 will get the port settings for the first 4 ports in the MX template as the Z1/Z3 only has four usable ports. Here's a link to further documentation: Managing Multiple Networks with Configuration Templates Hope this helps!

Mr_IT_Guy · ‎Jun 1 2018

Happy to be back and participating on the forums. Congrats to the other MOTMs and thanks to everyone who participates on the forums and helping the Meraki knowledge bank grow. @CarolineS, it's getting a bit warm here. My IT Director wants to know if you have anything to keep beverages frosty?

Mr_IT_Guy · ‎May 29 2018

I just spent the last 30 minutes going thru this. I was able to recreate the error you showed. The error only occurred when trying to summarize the IPs in Group Policy using "Custom network firewall & shaping rules". I am unable to combine multiple IPs into the one rule and the error message you showed is generated. This happens regardless of firmware version. When placed in Security Appliance > Configure > Firewall, the rule works without any issue. This leaves me to believe that it is a problem with group policy looking for only ONE IP when creating custom rules. Have you tried placing the rule in the Layer 3 section of the Security Appliance > Configure > Firewall page? This will apply to ALL groups on your MX unless you create a custom rule under group policy. If everyone is to be blocked from these IPs, my recommendation would be to place it there.

Mr_IT_Guy · ‎May 29 2018

Just tried on 13.28 firmware (latest stable). Can confirm it works and not a new feature on 14.xx firmware.

Mr_IT_Guy · ‎May 24 2018

@pwb, if you call support, they can move the MX64 into a new organization and retain all the current settings.

Mr_IT_Guy · ‎May 23 2018

Works for me!

Mr_IT_Guy · ‎May 22 2018

I do like this idea. I've wondered if there was a way to reward our Solution experts. That being said, what's to stop me from marking my own post as a solutions and thus inflating my numbers. I saw a post a few weeks ago (I don't remember which) where one community member posted a solution to a problem only for the OP to post a thanks and mark their own post as solution. It's going to have to require a bit more on your part @CarolineS to make sure that marked solutions are legit when calculating totals. I do like the idea of solutions being worth double though! I think a sound solution is worth more to the community. That being said, I'm ready to see @PhilipDAth hit over 200 in a month with a system like that!

Mr_IT_Guy · ‎May 17 2018

Meraki Sweaters!!!! Although that might be a bit too hot for Orlando in June.

Mr_IT_Guy · ‎May 15 2018

Using the email sign-ups go into my spam. This happens every time I sign up for a webinar.

Mr_IT_Guy · ‎May 3 2018

I had completely forgot that I was a part of the program. I got mine in the mail earlier this week. @Maui_Meraki_Dog was not happy with our new friend so now it's sitting on my desk at work.

Mr_IT_Guy · ‎Apr 18 2018

If it were possible to do this, I'd be SOOOOO HAPPY. Alas, every day I'm putting in wishes to make this a possibility...

About Mr_IT_Guy

Mr_IT_Guy

Community Record

Badges