https://documentation.meraki.com/General_Administration/Support/Ways_to_Contact_Meraki_Support ... View more

If the repeater AP cannot find a nearby gateway with a valid route to the internet, it will still broadcast SSIDs but won’t pass traffic.   Gateway AP Switches to Repeater Mode - Cisco Meraki Documentation ... View more

A very simple question: are customers at least receiving IP addresses? Have you opened a support case yet? ... View more

Teka a look at this.     Restricting Access to Cameras - Cisco Meraki Documentation ... View more

Você não consegue repetir o sinal (Mesh) de de equipamentos Meraki com equipamento de terceiros. Sem contar que a funcionalidade de Wifi do MX é limitada e também não possui WPS.   Mas talvez dependendo do tipo de autenticação você consiga estender o sinal no repetidor da Intelbras, mas o ideal seria realizar um teste antes. ... View more

I already have a different understanding than yours based on this other document. "This rule will evaluate the packet loss of established VPN tunnels and send flows matching the traffic filter out of the preferred uplink. If the loss, latency, or jitter thresholds in the "Web" performance rule are exceeded, traffic can fail over to tunnels on WAN2 (assuming they meet the configured performance criteria)."   https://documentation.meraki.com/Architectures_and_Best_Practices/Cisco_Meraki_Best_Practice_Design/Best_Practice_Design_-_MX_Security_and_SD-WAN/Meraki_SD-WAN#Adding_Performance_and_Policy_Rules ... View more

The failover logic is triggered if any one of the conditions is met, not necessarily all at once.   Meraki SD-WAN   Meraki SD-WAN - Cisco Meraki Documentation ... View more

As long as you are running Meraki firmware you can use mesh.   https://documentation.meraki.com/MR/Wi-Fi_Basics_and_Best_Practices/Wireless_Mesh_Networking ... View more

I suggest you open a support case. ... View more

Theoretically it shouldn't work, but have you tried declaring the Anyconnect network as traffic of interest on the peer side? ... View more

It doesn't hurt to double-check, if the problem persists I suggest you open a support case. ... View more

Are you entering the correct serial number? ... View more

Bigip is the key  ... View more

In your case, it is recommended to use a solution like Bigip. ... View more

You can give your feedback on the dashboard.   https://documentation.meraki.com/General_Administration/Other_Topics/Give_your_feedback_(previously_Make_a_Wish)#:~:text=1.,the%20%E2%80%9CHighlight%20Page%E2%80%9D%20tool. ... View more

Take a look at the documentation.   https://documentation.meraki.com/MS/Port_and_VLAN_Configuration/Configuring_Spanning_Tree_on_Meraki_Switches_(MS)#Set_Bridge_Priority ... View more

If WAN 2 is working without problems, I suggest you open a support case, as you will probably need to RMA the device. ... View more

Have you tried other browsers? ... View more

Caveats On the MX75 - The Third physical port is the designated backup port. Physical ports 1 & 2 become designated WAN 1 and WAN 2 ports.  On the MX85, MX95 & MX105 - The Fourth physical port is the designated backup port. Physical ports 1 & 2 become designated WAN 1 and WAN 2 ports. On the MX85, MX95 & MX105 - the Third physical port is disabled and unusable once MultiWAN is enabled The designated backup port cannot be changed to a different physical port SFP modules (fiber or copper) are required for physical ports 1 & 2 IPv6 is not supported on the Backup WAN uplink  Not all NAT features are supported such as Port Forwards, 1:1 NAT and 1:Many NAT   MultiWAN Backup Uplink - Cisco Meraki Documentation ... View more

You can try a few things, such as verifying the ADE token in ABM and Meraki, creating a new ADE profile with authentication disabled, restoring the iPad to factory settings and retrying setup, and avoiding URL enrollment unless you're using manual post-setup enrollment. If the issue persists,  I suggest you open a Meraki support case. ... View more

Are you full admin? ... View more

This is a reserved code in the 802.11 standard, meaning it's not officially defined with a specific cause.   The problem could be due to several reasons, such as a firmware update. Try the following if you haven't already.   Disable 802.11w on affected SSIDs. Test with Open SSID to rule out WPA2-PSK issues. Rollback firmware if the issue started after an upgrade. Open a Meraki support case with logs if the issue persists. ... View more

Você pode utilizar um Servidor Radius externo, a base da Meraki, tem várias formas, depende qual fica mais viável para você.   https://documentation.meraki.com/MR/Encryption_and_Authentication/Configuring_RADIUS_Authentication_with_WPA2-Enterprise   https://documentation.meraki.com/MR/Encryption_and_Authentication/Configuring__WPA2-Enterprise_with_Meraki_Authentication ... View more

So the IP used is from the Primary, if it becomes inactive the IP used is from the secondary when it takes over, in any case you can use the FQDN to connect and not worry about the IP. ... View more