Meraki

redsector · ‎Aug 19 2019

Hi, I got the same problem today with an MS250-48LP. There is no exceeding power consumption. The error suddenly appeared. I opened a case.

redsector · ‎Aug 15 2019

We solved several problems on our dell notebooks by doing a firmware update and driver update for the wifi network device.

redsector · ‎Jul 15 2019

Strange, all my networks are combined networks. I checked it with all networks. I can see the menue item in all networks.

redsector · ‎Jul 15 2019

Look at "network wide" - "clients". Choose the client. on the chart-pie choose "show details".

redsector · ‎Jul 15 2019

I have got 9 Networks updated to MS11.22, no issues, this are smaller networks up to 9 switches MS225, MS220, MS210 . 4 Networks are running on MS11.23, no issues, this are smaller networks up to 4 switches. Our main network ist still running with MS10.45 with 33 MS 225 and MS220 switches.

redsector · ‎Jul 15 2019

We have got all user ports untrusted even with MR accesspoints. No issues up to now (with MS10.45, MS11.22 and MR25.13 softwared networks/devices). Only the uplink-ports are trusted.

redsector · ‎Jul 15 2019

BrechtSchamp was right. I checked it out: Based on MS11.22 firmware; MS225, MS210 switches: First you have to enable Storm Control in "switch" -> "switch settings" by adding a rule. Then you have an additional "Storm Control" setting in the switchports (not on the MS120 and MS220 switches!) best regards.

redsector · ‎Jul 8 2019

Hi, I can set a Storm Control on Switch > Switch Settings and the rules. I also can switch on Storm Control on the switchports MS210, MS225 etc. (enabled / disabled). Does anybody know if there is an relationship? Does the rules only work when I switch on the Storm Control on the ports? Thank you.

redsector · ‎Jun 26 2019

My new gnome avatar. In Germany they are very famous named Gartenzwerge.

redsector · ‎Jun 26 2019

We have got MS225-48LP / MS120-8P / MS220-48LP switches with Firmware 10.45. There are a lot of Avaya IP-phones and Cisco and Meraki accesspoint connected. Non of the has any problems with PoE or LLDP . all phones are running in a voice-VLAN and PCs connected to the phone are running in a client VLAN. Its working well. Only some printers and Apple Macs are changing the link speed all the time. The users can work without any issues.

redsector · ‎Jun 24 2019

I had an MR33 that wasn´t booting any more after power reset. Only the orange light was on. No rainbow booting light. The switch said "no connection". I opened a case. And after checking and resetting the accesspoint they sent me a new accesspoint. The new accesspoint is running.

redsector · ‎Jun 4 2019

@SoCalRacer No. The Sonic Walls are in the headquarter. And we are planning to use MX in shops or small offices to connect to the headquarter.

redsector · ‎Jun 4 2019

Hi, I have got questions about Meraki MX. We are planning to install our first MX in a subsidary. We deside to use the MX68CW because of the LTE redundancy. Does anybody know if I can stack two MX68CW for hot standby or failover? In the headquarter we have two Dell SonicWall Supermassive 9200. Is that working with MX in the subsidary? thanks in advance

redsector · ‎Jun 4 2019

O.k. I tested a 10Gig copper SFP with an Meraki MS225-48LP switch. I used one of the 10Gig SFP-ports. The switch recognized the SFP and I could use it. The only thing is to take care of the length of the copper cable. Supported is 30m but we tested it with 40m (a good Cat6 cable) and it was working well.

redsector · ‎Jun 4 2019

No mails up to now.

redsector · ‎May 22 2019

🙌

redsector · ‎May 14 2019

I had the same issues. After updating firmware to 10.45 the error didn´t appear again.

redsector · ‎May 7 2019

Caroline, Thank you. It´s working. 👍 best regards

redsector · ‎May 7 2019

I will open a case.

redsector · ‎May 7 2019

It helped to shut lldp on Cisco classic devices and re-enable it again. Also shutting cdp and enabling lldp only helped (after waiting a couple of hours). Cisco classic: no lldp run (shutting lldp) lldp run (reenable lldp) no cdp run (shutting Cisco cdp) helping when the topology view is confused cdp run (reenabling Cisco cdp)

redsector · ‎May 7 2019

Hi, suddenly I can´t change my signatures for my community posts any more. The signature box is missing. I can´t see or find it any more. Here is the text of the community help: How do I create a signature for my posts? Your signature is text that appears at the bottom of your posts. To create your personal signature: Sign in to your community account. Go to My Settings > Personal Profile > Personal Information. Enter your signature text in the Signature box. Some communities let you use HTML in your signature. Check with a moderator if you have questions. Click Save.

redsector · ‎May 6 2019

Meredith, thank you. You made my day!

redsector · ‎May 6 2019

Some of the Cisco "classic" are the same. It´s strange we bought Cisco WS-C3850 switches with removabel power supplys for C15 , later we bought the same switches and the same power supplys (the same order number) and got C13 connectors on the power supplys. Really strange. The Meraki MS225 and MS120 are still delivered for the old C13 cables.

redsector · ‎Apr 25 2019

Yes I had the same issue. Switch to "all" cases then you can see the old and the new cases.

redsector · ‎Apr 25 2019

Voice VLAN / VLAN recognition is working independ of 802.1x RADIUS. The switch puts the IP-phones automatically to the voice VLAN in my networks. PC´s connected to the phones are running into the user VLAN.

About redsector

redsector

Markus Moses

Community Record

Badges