Meraki

redsector · ‎Jan 17 2023

I am eager to learn API programming for to manage my Meraki networks in a better way. Mayby Meraki offers lessons for this?

redsector · ‎Jan 17 2023

2023 a newly rebulit and reconstructed office floor with 3.800 square meters will be created with 26 * CW9164I-MR accesspoints and 10 * MS225-48LP switches. I am really excited.

redsector · ‎Jan 17 2023

Recently changed a warehouse and replaced old network hardware with Meraki devices: 22 new accesspoints (TT_AP1 to 16) are MR46E with wallmounted with the "big ears" Narrow Patch (MA-ANT-3-F6) and accesspoints TT_AP17 to 20 are ceiling mounted accesspoints with external bendable antennas Bendable Dipole (MA-ANT-3-B6). They are connected to two MR225-24P.

redsector · ‎Jan 17 2023

I attached a map. Accesspoints TT_AP1 to 16 are MR46E with wallmounted with the "big ears" Narrow Patch (MA-ANT-3-F6) and accesspoints TT_AP17 to 20 are ceiling mounted accesspoints with external bendable antennas Bendable Dipole (MA-ANT-3-B6).

redsector · ‎Dec 27 2022

😂no, 22 in one hall.

redsector · ‎Dec 2 2022

A little bit too many open issues...

redsector · ‎Nov 19 2022

Yes, here are the additional photos: Visit us at: https://www.thinkfun.com https://www.ravensburger.us

redsector · ‎Nov 18 2022

But: don´t you get error emails because Meraki accesspoints are not available any more, and dashboard misses them?

redsector · ‎Nov 18 2022

22 new Meraki MR46E accesspoints with big "ear" Narrow Patch (MA-ANT-3-F6) antennas in one of my warehouses

redsector · ‎Nov 11 2022

I had to do this for importing Catalyst 9500 into the Meraki Dashboards: adding the bold line on the switch config: line vty 0 4 length 0 transport input ssh transport output telnet ssh

redsector · ‎Oct 24 2022

Hello, according to the manual to view Cisco Catalyst 9500 switches in the Meraki Dashboard I used this manual: https://documentation.meraki.com/Cloud_Monitoring_for_Catalyst/Onboarding/Cloud_Monitoring_for_Catalyst_Onboarding_Guide But it fails altough all conditions met. It´s the error message: Device is not eligible for onboarding. Reason: Error: The switch is unable to connect to the TLS gateway eu.tlsgw.meraki.com to establish a tunnel connection. Verify routes and firewall rules are in place to allow communication on TCP 443." Review pre-onboarding requirements for more information: https://documentation.meraki.com/Cloud_Monitoring_for_Catalyst/Onboarding/Cloud_Monitoring_for_Catalyst_Onboarding_Guide#Pre-Onboarding I checked all to do´s and everything seems to be fine including the firewall config, the firmware version and so on. Then I tried to make (for test purpose) an ssh connection to the described eu.tlsgw.meraki.com per CLI direct from the switch, but then I have this message: Distri1#ssh eu.tlsgw.meraki.com % Connection refused by remote host also with the us site: Distri1#ssh us.tlsgw.meraki.com % Connection refused by remote host Is there anybody who has some experience to do this monitoring an Cat 9xxx with Meraki Dashboard? Any suggestions? Thank you.

redsector · ‎Oct 21 2022

It´s definitive solved with Apple TV OS 15.6 and MS switch firmware 14.33 (MS225-48LP switches)

redsector · ‎Oct 7 2022

o.k I understood. So I need only the Meraki dashboard license but not the DNA license for the full management with Meraki dashboard. The Video shows an example for this with an Cat 9300, so maybe it´s not poassible for the Cat 9200.

redsector · ‎Oct 7 2022

Ok. I need an DNA license to install direct on the switch and additional an Meraki license to manage it with Meraki Dashboard?

redsector · ‎Oct 7 2022

The license? (DNA or Meraki license?) Never heard about. Meraki switches licenses I put always in the dashboard not onto the switches.

redsector · ‎Oct 7 2022

sorry, but it says the same, fully managed with DNA license. But DNA license is not possible in Meraki Dashboard. "What about licensing? Fully managed Catalyst switches will need to have DNA Advantage (DNA-A) or DNA Essentials (DNA-E). Monitored Catalyst switches will use a Meraki license." this means: not managable in Meraki Dashboard, only monitoring. managable in DNA. Right?

redsector · ‎Oct 7 2022

The first link says: "What about licensing? Fully managed Catalyst switches will need to have DNA Advantage (DNA-A) or DNA Essentials (DNA-E). Monitored Catalyst switches will use a Meraki license" Fully managed devices need an DNA license. But I can´t put in the DNA license into the Meraki Dashboard.

redsector · ‎Oct 7 2022

First Link is only the monitoring, not the management version. You can buy an "montoring only" version and a "management" version, this seems to be an difference in the operating system.

redsector · ‎Oct 7 2022

Hello, Can I manage Catalyst C9200 switches in Meraki Dashboard? Do I need the DNA license or the Meraki Dashboard license, or both? My dealer is not able to answer this questions. He offers me always DNA-licenses with that switches. But I want to manage (not monitor) them at Meraki Dashboard. So I think I need Meraki Dashboard licenses for this switches. The thing is: I am buying since years the Meraki MS225-48LP switches. But once in the future they will be out of service, and then I have to replace hundreds of them. So I like to use newer switches now.

redsector · ‎Oct 4 2022

helped me a lot solving some issues: "General stability and performance improvements" Wireless firmware versions MR 29.2 changelog Bug fixes General stability and performance improvements AP performance may degrade over time (Wi-Fi 6 APs) AP may stop broadcasting beacons on WPA2 configured SSID (MR53E) AP may lose Cloud connectivity for an interval of time (Wi-Fi 6 APs) SES-imagotag ESL status may display as gray even when ESL is functioning normally (Wi-Fi 5 Wave 2 and Wi-Fi 6 APs) SES-imagotag 2.4GHz Wi-Fi Co-Existence might not work on MR36H Wireless firmware versions MR 29.3 changelog Bug fixes General stability and performance improvements Intermittent low power mode (MR53, MR56) SES-imagotag application bootloop (MR30H, MR33) Honeywell printers unable to connect to hidden SSID (Wi-Fi 6 APs) Wireless firmware versions MR 29.4 changelog Bug fixes General stability and performance improvements ‘No DHCP response’ error using L3 Roaming ‘DNS misconfigured’ error while using Umbrella DNS

redsector · ‎Oct 4 2022

Meraki firmware update.

redsector · ‎Oct 4 2022

Use an new firmware! I had similary issues.

redsector · ‎Sep 27 2022

I am really happy now with firmware 29.3 on all my networks with an amount of different MR accesspoints.

redsector · ‎Aug 14 2022

🍺a beer on you!

redsector · ‎Jul 1 2022

Would be nice to keep a VLAN list with names on the switches like on Cisco "classic" switches with the command: sh vlan

About redsector

redsector

Markus Moses

Community Record

Badges