Are there any AP's with a management address of 10.129.5.2-127? ... View more

  I see them online but not from meraki. This is the suported list. But it could stil work https://documentation.meraki.com/General_Administration/Cross-Platform_Content/Small-Form_Factor_Pluggable_(SFP)_and_Stacking_Accessories   Did you ever hit near 1Gbit up or down on any AP? You would need to use 160mhz channels to go past 1Gbps on a normal 2x2 wifi client   How are you going to power the AP? Poe adapter?   I personally wouldnt bother upgrading any non 6Ghz capable AP to 2.5Gbit     ... View more

When you look at stack b switch2. Who does that switch report as root?   ... View more

Hi,  Is the device online on the dashboard? The password should be on your meraki dashboard. Network-wide >general> device config   You can also try,  use the serial number of the device (upper case letters and dashes) as the username with no password.   If it doesnt reset pressing the button 30 seconds then you should contact meraki support     ... View more

That doesnt work,   I do know its possible with a one armed concentrator-hub design ... View more

Impact of ips is big. I think you could get more speed using more clients/seperate data streams, but max would be like 300/400Mbps   https://documentation.meraki.com/MX/MX_Sizing_Information/MX_Sizing_Principles#Performance_Data   You could look into using traffic exclusions to get some more throughput on some data sessions https://documentation.meraki.com/MX/Content_Filtering_and_Threat_Protection/Trusted_Traffic_Exclusions   ... View more

By default everything is handled in the "normal" queue. Best is to mark voice with dscp ef on the client so that it would start using the realtime pq ... View more

Meraki support  2+ 1 backup wan. https://documentation.meraki.com/MX/MultiWAN_Backup_Uplink   Vpn and mail are services you could move to the lan side with static routes or bgp? wan2 can then be used for backup internet   https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/SD-WAN_and_Traffic_Shaping   Yes you can put in urls to check in which category they fall. https://documentation.meraki.com/MX/Content_Filtering_and_Threat_Protection/Content_Filtering/Content_Filtering_Troubleshooting#Category_Filtering I dont know if it works with starlink ipv6, but i read it also support ipv4? ... View more

These are switches sending bpdu on native vlan, and meraki only support stp, so just a single topology (not per vlan).    Most designs you looking at are probably using routers or switches using layer3 ports. (Like a catalyst with  # no swithport)   I supose you could disable stp on the ports using this design, buttttt a configuration/mistake in the future could lead to a loop. I think i wouldnt use meraki switches for this design ... View more

1500   And if you want to send it throught the autovpn then 1432 ... View more

Do you have link to that document?   Documentation of Dhcp for vlans should be here https://documentation.meraki.com/MX/DHCP/DHCP_Services   By default it would assign its own vlan ip as gateway for the client devices. ... View more

Use the outbound rules. Inbound ipv4 sessions are blocked by default   https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/MX_Firewall_Settings#Outbound_rules ... View more

What mx device and firmware you have?   Do you also have a MR ? Mr should still send flow logging   https://documentation.meraki.com/General_Administration/Monitoring_and_Reporting/Syslog_Event_Types_and_Log_Samples   A flow is basically every new session a client makes https://community.meraki.com/t5/Wireless/What-Is-Flows/td-p/36277 ... View more

Can you ping the dns servers or do nslookups to that server and start firewall logging. See if something get blocked/allowed https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/Firewall_Logging ... View more

End of sale is 1 year away and end of support is 2030 so if they work fine i would keep them. Unless 9300 hw+lic is cheaper ... View more

I should be under network- wide > general   Or org> settings >snmp   https://documentation.meraki.com/General_Administration/Monitoring_and_Reporting/Meraki_Device_Reporting_-_Syslog%2C_SNMP%2C_and_API#SNMP_Configuration   https://documentation.meraki.com/General_Administration/Monitoring_and_Reporting/SNMP_Overview_and_Configuration#Configuration ... View more

Did you add vlan 20 on the trunk between mx and core switch?   Did you remove the static route for vlan20 from the mx to the coreswitch?   Did you remove the vlan 20 svi from the switch? ... View more

On 30.7 has problems related to customers with many ssid configs. But the problems described in release notes sound different then yours. ... View more