This seems like it might be more related to the PC settings. I should double check SMB settings. Check if you can browse to the share from your PC to the other PC.   On the Meraki side I would check the group policies for all these devices are the same. Then do a packet capture on the working setup. Then a packet capture on the non working setup. Compare those and see if you see any issues.   Also for reference what Meraki equipment are you using (MX64/MR33/MS120)? ... View more

I believe you will run into issues with any solution especially if you don't have access to Azure, since most of the config needs to be done properly there first.   Here is some info on different solutions, but yes I would say vMX is best, but its pretty costly.   1-vMX100 https://documentation.meraki.com/MX/Installation_Guides/vMX100_Setup_Guide_for_Microsoft_Azure   2-Custom Azure VPN Setup http://www.ifm.net.nz/cookbooks/meraki-vpn-to-azure.html   3- Policy Based VPN https://www.virtualizationhowto.com/2017/08/configure-meraki-to-azure-site-to-site-vpn/   ... View more

Possible expired cert? ... View more

DNS or MDNS might be a place to look. Also I would recommend doing a packet capture on both devices when this issue is happening. I have found many issues making sure Chromecast will work in certain networks. ... View more

Also might try searching for a 3D print of a replacement ... View more

Queued in my podcast playlist! ... View more

I found a link in the documentation site. https://documentation.meraki.com/Architectures_and_Best_Practices/Cisco_Meraki_Best_Practice_Design/Best_Practice_Design_-_MX_Security_and_SD-WAN/Meraki_Auto_VPN_General_Best_Practices   I tried looking for these, my bet is that it is a stencil pack or platform Meraki is using for topology. My guesses would have been draw.io or LucidChart, but I couldn't find similar shapes on either.   @CameronMoody or @MeredithW might be able to help find out what they use internally for these drawings. ... View more

Is there an upsteam possibly NAT device from the MX on either uplinks?   Also to confirm is this MX67 or MX84? ... View more

Can you provide links? ... View more

New Post https://community.meraki.com/t5/Off-the-Stack/Visio-Shapes/m-p/721   Legacy Post https://meraki.cisco.com/blog/2018/12/our-topology-icons-speak-volumes/ ... View more

It can be done with VPN access, although I think you will run into a headache with HVAC techs with that. Most of the time we allow the ports (if secure) from their IP (Office) only that way they can manage their devices, but don't have a bunch of security to deal with. Also if there is a breach then you can rule it as it was done form their IP, instead of one of your auth'd users via the VPN. ... View more

Not available at this time to my knowledge. ... View more

Did this work at some point or is this a new deployment?    On the client machine network adapter, IPv6 turned on or off?   I assume if possible to connect physically into the datacenter then this issue does not occur? ... View more

I am fairly sure SplashAccess doesn't work with the MX internal wireless. If it doesn't I don't think it is intended to.   I know this is for an MR, but did you follow these instructions? I was able to do that with a MX65W, although I didn't setup the SplashAccess back end. https://documentation.meraki.com/MR/MR_Splash_Page/Splash_pages_with_PayPal_or_Credit_Card_Billing/#Splash_Access ... View more

Can't stand when providers do a /30 on business circuits. ... View more

Another reason to script this and use @Nash 's scripts! ... View more

I don't see the LAN Isolation in there. ... View more

This doc says it is limited to first 24 ports https://documentation.meraki.com/MS/Port_and_VLAN_Configuration/Restricting_Traffic_with_Isolated_Switch_Ports ... View more

AIR-PWRINJ30= and MR34    Might try the suggestions in that thread. I don't think there is an official answer, but those work on most Meraki devices. ... View more

Europe +44 203 808 7003 ... View more