MX LAN Trunk Port with Non Meraki Switch

SOLVED
Luffy
Getting noticed

MX LAN Trunk Port with Non Meraki Switch

Hi,

 

I am looking for anyone who has experience about my subject.

Customer has a cisco catalyst switch with 3 VLANs. So I tried to connect between MX100 and Catalyst Switch with Trunk Port(dot1q).

But I was failed to connect.

 

MX100-MS225 Trunk Port Test was good.

Cisco-Cisco Trunk Port Test was good.

MX-Cisco SW Trunk Port Test was failed.

 

I don't know why this test was failed.

 

1 ACCEPTED SOLUTION
PhilipDAth
Kind of a big deal
Kind of a big deal

So VLAN1000 is working but VLAN2000 is not working.  2000 is in the extended VLAN range (not part of the standard VLAN range).  It should work.  The issue will be something to do with the use of the extended VLAN range.  Let me think about it more.

View solution in original post

12 REPLIES 12
PhilipDAth
Kind of a big deal
Kind of a big deal

What specifically is failing?

 

Lets pretend you wanted to trunk VLAN1 (Native) and VLAN100.

 

On your Catalyst switch (like a 2960-X) you would have something like:

interface Gigabit 0/1

 switchport mode trunk

 switchport trunk allowed vlan 1,100

 

On your MX you would have something like:

Screenshot from 2017-10-30 19-32-21.png

Please refer my message.

Please refer my message.
MilesMeraki
Head in the Cloud

You'll have to supply some more information. As per @PhilipDAth's reply this clearly specify's what's required from a configuration aspect, the only difference is you'll have to configure the 3 VLAN's rather than 2?

Eliot F | Simplifying IT with Cloud Solutions
Found this helpful? Give me some Kudos! (click on the little up-arrow below)
Adam
Kind of a big deal

This article has some helpful details that we used when doing a similar configuration to you.

 

https://documentation.meraki.com/MS/Port_and_VLAN_Configuration/Recommended_Configuration_for_Trunk_...

Adam R MS | CISSP, CISM, VCP, MCITP, CCNP, ITILv3, CMNO
If this was helpful click the Kudo button below
If my reply solved your issue, please mark it as a solution.
Luffy
Getting noticed

Hi Adam,

Thank you for your reply

 

I already saw the article.

But It was no helpful to me.

 

Thank you,

 

Hi PhlipDAth, Thank you for your answer. I already set same as you.

Please refer the below pictures.

 

1. MX64 Setting Page

MX Setting1.jpg

2. MX64 Ping test from MX64 to Cisco Switch

 

MX Setting2.jpg

 

3. Cisco Switch Setting and Ping Test

Switch Setting.jpg

 

 

PhilipDAth
Kind of a big deal
Kind of a big deal

So VLAN1000 is working but VLAN2000 is not working.  2000 is in the extended VLAN range (not part of the standard VLAN range).  It should work.  The issue will be something to do with the use of the extended VLAN range.  Let me think about it more.

PhilipDAth
Kind of a big deal
Kind of a big deal

On your 6500 have you got "spanning-tree extend system-id" configured globally to allow the passing of the extended VLAN range?

PhilipDAth
Kind of a big deal
Kind of a big deal

Are you able to change from using a VLAN ID of 2000 to a number that is 1001 or below?

Hi PhilipDAth,

 

Thank you for your great answer.

I resoved this problem.

This is VLAN issue.

 

So Meraki doesn't support extended vlan's?

Get notified when there are additional replies to this discussion.
Welcome to the Meraki Community!
To start contributing, simply sign in with your Cisco account. If you don't yet have a Cisco account, you can sign up.
Labels