Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About soundman353
soundman353
Here to help
Member since Jul 6, 2018
Mar 15 2023
Kudos given to
Community Record
19
Posts
2
Kudos
2
Solutions
Badges
Mar 15 2023
10:18 AM
I have a date with my warring. I tried looking in the release notes and searching on this forum for possible reasons. I agree with you; I don't want to jump to a stable release candidate unless there is a security issue or something similar.
... View more
Aug 17 2020
1:40 PM
1 Kudo
I applied the Stable Release candidate firmware, and the problem seems to be solve.
... View more
Aug 4 2020
7:51 AM
Since it's happening again, I think I will try the stable release.
... View more
Jul 31 2020
7:58 PM
1 Kudo
The reboot fixed the issue.
... View more
Jul 31 2020
7:45 AM
The only firewall (other than hosts firewalls) is the Meraki MX100. I will power cycle the unit tonight and see if that clears everything.
... View more
Jul 31 2020
7:18 AM
I can SSH to the any of the end points from within the LAN, so there is services listening. It was the on the MX Client VPN via the Meraki dashboard.
... View more
Jul 31 2020
5:52 AM
I did Wireshark run on the Client VPN, MX LAN and the Core Switch. I see the traffic on the Client VPN capture but no where else. Every request is answered with a retransmit from the all of the devices I am trying to SSH.
... View more
Jul 30 2020
12:11 PM
Hello All, I tried to SSH into a few machines over the Client VPN today, all of them have timed-out. It was working earlier this week and no firewall changes between now and then. Any ideas? Shawn
... View more
Jun 18 2020
6:51 AM
The solution that worked for me was to place a switch in front of the remote MX to receive the trunk port from the ISP. The remote MX is connected to an access port. I used one of the public IP's that was assigned to us for the uplink, and set that as a static IP. On the main office side I placed a switch between the router and the main MX. The router and MX are connected to access ports, while the PTP connection is a trunk port. All of the ports are on the same VLAN. Thanks for the help.
... View more
May 11 2020
5:06 AM
If I have the ISP add the PTP VLAN to trunk port that feeds my router, can I use the router instead of more equipment? So the remote MX would have an IP of 10.0.0.3/31 and the router would be 10.0.0.4/31? The gateway for the remote MX would be 10.0.0.4 correct? I would need to have a default route on the router to the main MX?
... View more
May 8 2020
2:09 PM
Hopefully my diagram helps. This is the current setup. The main site MX is routed mode, as it is firewall for the system. I do have an internet connection at the remote site.
... View more
May 8 2020
10:57 AM
Hello All, I am trying to setup Point to Point connection between two MX's. I have a copper handoff at the main office and a LX optic at the remote office. Both ports are being tagged by the ISP and have no IP addresses. At the main campus I have an 2nd copper handoff going to a router, with two vlans that are my internet connection. How can I setup up the AutoVPN with failover? In the Meraki guides the routers, and they have IP addresses. I have read the guides but now I am just confused. Thanks, Shawn
... View more
Kudos given to
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 6233 | Jul 31 2020 7:58 PM | |
| 4601 | Jun 18 2020 6:51 AM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 1 | 5989 | |
| 1 | 6233 |
© 2025 Cisco Systems, Inc.
