Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About TheAlchemist
TheAlchemist
Getting noticed
Member since Jul 19, 2022
Jul 16 2024
Community Record
68
Posts
18
Kudos
0
Solutions
Badges
Jun 18 2024
9:36 AM
Sure, think it will tell WAN port utilization , that would be good enough but wont tell how much internet bandwidth is being made available by ISP.
... View more
Jun 17 2024
12:47 PM
Actually, not Meraki but, have used a product where the router provides in a graph, sensed (or available) bandwidth up/down and then the actual bandwidth consumed up/down. So, was curious to know, would there be a way to get such stats while using Meraki MX.
... View more
Jun 17 2024
11:52 AM
So, would SolarWinds be able to able to sniff and tell how much bandwidth is being made available by ISP even though clients connected to MX would be using less . e.g. 500 Mbps uplink/downlink is made available by ISP while actual usage is of 100 Mbps uplink/downlink. Concern is to understand that provided ISP bandwidth is not dropping from 500 Mbps symmetrical to say 200Mbps symmetrical.
... View more
Jun 17 2024
10:51 AM
Hello, Wanted to understand if there is a way to check internet speed i.e. download/upload speeds available on a WAN connection without running any speed test. If there is a way to check on internet bandwidth being provided without running speed test. Concern is to know whether available bandwidth (up/down) fluctuates or not and speed test is not an option as it would affect live video streams running off the same internet. Thanks
... View more
Feb 4 2024
4:03 PM
Switch settings show MTU size set of 9578 (Jumbo frames) by default. As per the instructions you shared in the link, I cannot ping any public DNS over MTU 1472. Think Public internet does not support Jumbo frames so MX would be limited by max 1500 but withing MS switches in our network, Jumbo frames should pass through? I think.
... View more
Feb 4 2024
3:26 PM
Yes, on clicking the message on alert it takes to the Switch and highlights the port.
... View more
Feb 4 2024
1:18 PM
Below alert showed up on Meraki dashboard >Alerts>Device Health. What would this refer to? and could it lead to the link /connection going down ? "Oversized or undersized packets detected." "Detecting a very high proportion of oversized or undersized packets on SWXX"
... View more
Aug 11 2023
2:27 PM
1 Kudo
This is for any urgent case scenario where we are left with no choice and definitely for a temporary use case.
... View more
Aug 10 2023
5:49 PM
I have always setup with a Mx or a Z1 device but a layer3 MS switch is capable of running on its own in Meraki network. I could create a network in Meraki based on ONLY a switch. But, can I use it as a flat switch ? I guess not. And as @alemabrahao mentions, where can I setup the uplink info as I can normally do on an mx/z1 device.
... View more
Aug 10 2023
3:07 PM
As it is possible to create a network using just a switch without a security appliance, is it possible to feed that switch dirty internet and use it.
... View more
May 5 2023
7:06 PM
2 Kudos
For an enterprise license, you can get info on : Air Marshall events, Flows, URLs, Wireless event log, Switch event log, Appliance event log.Flows would give you more info on source, destination, MAC and protocol.
... View more
May 3 2023
5:04 PM
4 Kudos
Thanks for taking out time to talk to me. Its a great learning platform and answers by all contributors are greatly appreciated. BTW , I have a son not a daughter.
... View more
Apr 19 2023
3:22 PM
I think device utilization in Summary Report is not the same as CPU utilization and as @ww already mentioned, only Support can see CPU utilization and it is not visible on Meraki Dashboard to users. Is there any API call which can provide such info?
... View more
Mar 11 2023
2:45 PM
Actually, even after disabling load balancing and Active-Active Auto VPN , still MX-250s continue to show latency spikes on both ISPs at the same time for unknown reasons. No particular event is captured at the mentioned time which might point to this latency spike.
... View more
Mar 2 2023
3:56 PM
Actually need 1xconnection to a WAN port and 1x connection to a LAN port. But, yes better simply test.
... View more
Mar 2 2023
3:35 PM
It does actually, there are 10Gbps CWDM SFPs by Cisco. Its just Meraki has no mention of CWDM. https://www.cisco.com/c/en/us/products/collateral/interfaces-modules/transceiver-modules/datasheet-c78-734047.html
... View more
Mar 2 2023
3:31 PM
Mar 2 2023
3:13 PM
Sorry did not mention before, but looking for a 10Gbps connection.
... View more
Mar 2 2023
2:55 PM
Oh ok, so a CWDM SFP will not work with Meraki. Are you sure from any use case before or is it based on any internal information.
... View more
Mar 2 2023
1:12 PM
Does Meraki MX appliances support CWDM fiber SFPs using wavelengths 1470-1610 nm.
... View more
Feb 23 2023
6:53 PM
So pretty much each access point from Meraki can cover 31416 sq m or 338159.01 sq feet of area?
... View more
Feb 23 2023
2:41 PM
Is there a datasheet for coverage area (square feet) or a coverage radius for Meraki Access Points.
... View more
Feb 10 2023
10:21 AM
Can the per day license be applied and used in an on demand use case? If we use an mx appliance for 3 weeks in 6 months then is it a possibility to use PDL model?
... View more
Feb 9 2023
9:54 AM
If I would need a MX appliance for 6x months in the year, would it better to have 1x day license or an annual license.
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 4 | 4750 | |
| 4 | 7130 | |
| 2 | 620 | |
| 2 | 4400 | |
| 2 | 4280 |
© 2024 Cisco Systems, Inc.
