Meraki

Community

About amirmin

Re: Site-to-Site VPN over MPLS

by in Security & SD-WAN
‎Oct 10 2021 10:01 PM
‎Oct 10 2021 10:01 PM
Hi @Bruce @cmr , thanks for the explanation. It means each WAN interface must be able to reach the internet (doesn't matter how) but as long as it can reach the internet on their own then it should be fine. Thank you ! ... View more

Site-to-Site VPN over MPLS

by in Security & SD-WAN
‎Oct 7 2021 12:44 AM
‎Oct 7 2021 12:44 AM
Hi   Currently I have this setup. Both Hub and Spoke running in routed mode with NAT enabled.   Hub (MX68) WAN 1 > MPLS (Private network) WAN 2 > direct internet connection via MG21   Spoke (MX68) WAN 1 > MPLS (Private network) WAN 2 > direct internet connection via MG21   I have put a Router in between the Hub and Spoke to simulate for the MPLS (private network) as below. Spoke (WAN1 interface) - Router - Hub (WAN 1 interface)   I can see the Auto-VPN tunnel is created but it is only via MG21 (WAN 2 interface). How do I establish an autoVPN tunnel over the MPLS (private network) ? Does it require a route leak in the MPLS network ? ... View more
Labels:

Re: MX68CW WAN failover to LAN 1

by in Security & SD-WAN
‎Sep 23 2021 11:35 PM
‎Sep 23 2021 11:35 PM
Hi @Bruce    Thank you clearing that up. Now I understand after going through the documentation @ww about the route priority. Gonna give it a try ! Thanks ! ... View more

Re: MX68CW WAN failover to LAN 1

by in Security & SD-WAN
‎Sep 23 2021 8:27 PM
‎Sep 23 2021 8:27 PM
Hi @Bruce    For options no.2, did you mean by making a custom static/default route to LAN 1 (which have a path to the internet/MetroE). Then if so, we still need to choose the primary uplink for the WAN 1 or WAN 2, lets say its WAN 1. So how is the selection will be, does a default route supersede the Preferred WAN 1 uplink ?   Thanks. ... View more

Re: MX68CW WAN failover to LAN 1

by in Security & SD-WAN
‎Sep 23 2021 8:22 PM
‎Sep 23 2021 8:22 PM
Hi @ww    Yes, that is what I have in mind, perhaps if Meraki can do it in the background for MX67 and wondering if they are planning to carry the factory settings to the MX68CW. ... View more

MX68CW WAN failover to LAN 1

by in Security & SD-WAN
‎Sep 23 2021 9:58 AM
‎Sep 23 2021 9:58 AM
Hi,   I have a setup of MX68CW with 3 WAN uplinks. Below is to summarize the design,   MX68CW Ports WAN1 - MPLS WAN2 – MG21 LAN1 – Metro E LAN2 – Local LAN   Desired Outcome - Wants to unplug WAN1 to failover to LAN1/Metro E   By design, if I have both WAN1 and WAN2 occupied, WAN1 fails over to WAN2. I want the order of failure to be WAN1 > LAN1 > WAN2 ? I have tried and tested but to no avail.   Has anybody ever tried this before? I read the deployment guide that in MX67 we can toggle the LAN port, thus I assume it can somehow can be done in MX68CW. ... View more
© 2024 Cisco Systems, Inc.