Is it possible to Geo-Fence on an MX-250? ... View more

Since 6:00 AM today. my devices have been alerting .   Has anyone else seen this.   I reached out to Meraki with a case and they suspect it is on their backend ... View more

I have a Vlan1 with address 172.16.12.0/23   DHCP is enable for this subnet   I  am running  low but not dangerously low on free addresses   To grow the DHCP is it just a matter of  changin the addressing and vlans   From 172.16.12.0/23 To 172.16.12.0/22.   Is there any impact on the users since now the Subnet MASK has changed? ... View more

I have 4 vlans VLAN 12 Corporate can go anywhere VLAN 6 LAB can go anywhere Guest only goes to the internet since  it is wifi VLAN 3 VENDOR LOCKED systems I would like to  only permit all wired hosts on VLAN 3 to go to a list of specific URLS.   Is this possible? ... View more

Firewall Layer 3 Inbound rules Inbound traffic will be restricted to the services and forwarding rules configured below. Inbound firewall logging   Has anyone enabled this to a syslog server and what kind of performance hit.  We have 2 gig of traffic   1.5 gig out .5 gig in ... View more

how do you determine the source IP if you are syslog logging  to an on premise host ... View more

Our IOT devices have grown in number SSID  Lab WiFi using VLAN 6 nearly exhausting the DHCP scope a /24 that cannot be remasked. I have VLAN 32 with lots of address a /22 which was original just used as a test  for an SSID Is reassigning the VLAN from 6 to 32 on SSID FN Lab WiFi a simple alternative to grow addresses? I imagine all device will need to request a new IP?   What will trigger the clients to reIP? I will rename the VLAN 32  to IOT for consistency ... View more

Is there a way to export the VPN user list? ... View more

The MAC addresses reported  are all non registered.   Worked with support for a Packet capture and was led to believe it was a ring doorbell. Asked the co tenant to turn off the door bell.  Issue exists still.   Has anyone seen  this similar issue?   Jan 3 13:45:07 FN285-WAP2     AP / client flood radio: 1, state: end, alarm_id: 6318  more » Jan 3 13:45:00 FN285-WAP2     AP / client flood packet: beacon, radio: 1, bssid: E2:CB:AC:90:4B:26  more » Jan 3 13:44:57 FN285-WAP2     AP / client flood radio: 1, state: end, alarm_id: 6317  more » Jan 3 13:44:49 FN285-WAP2     AP / client flood packet: probe_resp, radio: 1, bssid: EA:CB:AC:90:4B:26  more » Jan 3 13:44:27 FN285-WAP2     Single device packet flood radio: 1, state: end, alarm_id: 6316  more » Jan 3 13:44:27 FN285-WAP2     AP / client flood radio: 1, state: end, alarm_id: 6315  more » Jan 3 13:44:26 FN285-WAP2     Single device packet flood packet: probe_resp, device: EA:CB:AC:90:4B:26, radio: 1  more » Jan 3 13:44:19 FN285-WAP2     AP / client flood packet: beacon, radio: 1, bssid: 0A:8D:CB:71:42:DE  more » ... View more

  I wish to create a tunnel form my office ( Meraki). to a small warehouse (Palo Alto Networks)   I believe I may need IKE V2 since I wish to communicate to multiple subnets/ SA/encryption domain     172.17.12.0/23, 172.16.2.0/24. --- MERAKI.      <-> PAN 172.16.101.0/24 172.16.104.0/24   In I needed to I could  always supernet 172.16.96.0 /20.   Does a PAN to Meraki how to exist?  I have wan 1 and wan 2 on my meraki which may mean 2 tunnels initiated from the pan   Thank you ... View more

Looking for MX250 USB Backup setup procedures   Installing the modem on the Primary Member   Is there a chance for disruption when adding the device? ... View more

MS410 pair in a stack vmnic0 on stack member 1 port 13 vmnic1 on stack member 2 port 13   Currently not configured as a LAG   port settings are trunk with the same native VLAN.   The Vswitch with the port teamed with default settings seems ok except  when I unplug  vmnic0. I lose the server. When I enable VMNIC0 again I do see the port go to blocking.   Any ideas or suggested best practice?   ... View more

STEP 1   I am adding an SSID to evaluate a cloud radius solution I plan to tag 1 AP initially ( later tag a few more). I have 45 total APs   When I activate that SSID do I expect anything  across my network or does the SSID  just show configured on the AP.   STEP 2    When I  remove the availability setting for tagged value and  it is set on all 45 APs do I expect anything.   I am asking since I want to  do STEP 1  during the day possibly.     Thank you in advance ... View more