Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About WTorres
Community Record
20
Posts
3
Kudos
0
Solutions
Badges
Feb 20 2024
4:48 PM
Yes , I agree with you, not worth the headache. I will follow your advise and create a separate SSID for the third radio. Thank you!
... View more
Feb 20 2024
4:26 PM
Thanks for your input. We have considered using separate SSIDs however, What I would like to know is what will happen if we stay with the same SSID. Will this create disconnects when roaming?
... View more
Feb 20 2024
4:06 PM
Good evening. I have a network with mixed MR56 and MR57 APs using WPA3 authentication. I am considering enabling the third radio (6GHz) on the MR57. However, I am not clear on what would happen to my clients when they roam from 6GHz to 5Ghz radio. Can someone provide some insight on this? Thanks in advance.
... View more
I completely agree with @DevilWAH The issue was originally reported from Chromebook devices disconnecting or reporting poor client experience, eventually all devices with no exceptions were reporting the same anomalies. I also noticed AP performance was poor ranging from 90 to 17% I rolled back to 28.7 with the help of TAC last night and can confirm that all my client devices are back to normal this morning. As stated by @Schwa87 this rollback may not be for everyone.
... View more
Last night I downgraded a couple of schools to 28.7 + disabled Client balancing. High density networks, more than 100 MR56 each. So far no complains coming from the users and the logs are clean. Will keep and eye on them and update everyone.
... View more
I'm glad you were able to resolve the issue on your Windows devices however, I see this issue across all my client devices and it seems to be mostly affecting 802.11ax, 802.11ac as reported by @DBlum
... View more
Experiencing the same MR46 MR56 29.4.1
... View more
Oct 19 2022
7:08 AM
Thank you so much for your help! I will open a TAC ASAP and report back on this thread.
... View more
Oct 19 2022
6:13 AM
Current interference. Manually updating auto channels does help and have done it multiple times. Is there a way to block interferers that are not on my network?
... View more
Oct 19 2022
5:36 AM
My classroom APs are configured with an RF profile using AutoChannel assignment, which of course will assign radios to channels with low interference. Captured this morning.
... View more
Oct 18 2022
6:42 PM
MR56 network, clients are reporting disconnects in multiple classrooms. I'm seeing the following SSIDs when viewing "Interfering APs" in Air Marshal. My APs are on 20MHz (red circles ) channel 44 I highlighted in green what I believe could be causing interference (80MHz) channel 44+ Not sure if this is the issue since these (dashcam devices) are not on my LAN and are probably broadcasting from cars that are parked nearby. Thanks in advance for any constructive advice.
... View more
Oct 9 2022
11:54 AM
This is a High School. We created a Guest SSID with a different VLAN just for them with limited bandwidth for their personal devices. I agree this is a very high number hence, I'm looking to put in place all the relevant advise I can find in this community. Thank you for input!
... View more
Oct 8 2022
8:29 PM
I have seen between 1500 to 2000 devices during pick hours, and have thought about setting limits per SSID since 2Mb per user seems to create performance issues I read on a difference post that if you have 30APs and want to create a limit of 30M you will have to set SSID limit to 1Mb, 30/30 = 1Mb Can I apply the same logic in my network? 100Mb/180 APs = 550Kbps Per-SSID bandwidth limit
... View more
Oct 8 2022
4:45 PM
I need advice to limit the bandwidth for our guest users. Meraki school with 180 APs (MR56) 500Mb up down. Question, what would be the best recommended settings to allow a maximum of 100Mb to the guest users without affecting client performance. Currently using "Per-client bandwidth limit (2Mb) Any other ideas are welcome!
... View more
Mar 14 2021
3:19 PM
Lets say that I put the printers on VLAN 20 and the Students on VLAN 10, if using IPSK How would my printer Group Policy look like? Layer 3 Firewall, Layer 7 FIrewall, etc
... View more
Mar 14 2021
2:57 PM
My clients and Wireless printers are on the same VLAN, printers are not configured statically. I would like to use IPSK and create a separate group policy for students and one for printers. Most of my printers are Lexmark printers with airPrint enabled.
... View more
Mar 14 2021
2:01 PM
Hi everyone, I need recommendations to build a Printer Group Policy Using IPSK MR56 Thank you.
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 3 | 48668 |
© 2024 Cisco Systems, Inc.
