Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
- About adten
Community Record
16
Posts
0
Kudos
0
Solutions
Badges
12-15-2020
11:14 AM
Many thanks PhillipDath From AWS end, the instance status is Running.
... View more
12-15-2020
09:31 AM
Infact, all ports are allowed for now. This was on purpose to ensure there are no restrictions at this point. Despite allowing all ports, the situation remains same.
... View more
12-15-2020
08:54 AM
Hi Guys, I need some help on vmx-l. We recently added vmx-l to the dashboard with the aim of integrating to AWS. All configurations have been done on both AWS and Meraki dashboards but the vmx-l is still unable to connect to Meraki Cloud. The TCP port 7734 is already permitted on the dashboard, instance already created with network interface attached on , VPC, subnets and route table updated on AWS and certified ok by AWS support. We have also tried to regenerate the AWS token, yet the situation remains the same. In case you have faced a similar issue, kindly share how this was resolved. Thank you
... View more
11-20-2020
07:53 AM
I am referring to Meraki spokes. Thanks
... View more
11-20-2020
05:07 AM
Hi Guys, We are planning to replace our current concentrator hub MX 100 with an MX 450 and looking for an option that will not require any re-configuration of the spoke sites (about 234). Kindly share your experience if you have done a similar task in the past and what to watch out for. Many thanks
... View more
11-05-2020
05:41 AM
Yes correct, the large supports only AWS and Alibaba Cloud. As for Azure requirement for vmx small, perhaps more details will emerge in coming days.
... View more
11-04-2020
10:23 AM
Thanks for the response. Though, I have not seen the announcement as well but hoping it comes out soon. Thanks for the link
... View more
11-04-2020
08:54 AM
Hi Guys, I understood Meraki announced new release of Meraki vmx today. Please anyone with a link to the announcement; I need some details on the new product. Thank you
... View more
10-15-2020
02:03 AM
Hi cmr, Thanks for the response. But I need clarification on 4 points - 1. In the approved setup you referenced, is it only one LAN port on each Meraki MX device that should be connected to stacked switches 2. Is a virtual IP required for these two Meraki devices or only physical IPs will suffice 3. If physical IP addresses are required, how will the routing be done to ensure failover occurs in the event one of the devices fail 4. In a situation where you have only two WAN links, can they be connected one per Meraki device ? Thank you
... View more
10-12-2020
02:42 AM
Hi, Please does anyone have experience with deployment of HA for two MX 67 using VRRP. We are planning to deploy HA for two MX 67 using VRRP and need some helpful hints for the implementation in such a way that Dual Active issue will be avoided. Thank you
... View more
08-21-2020
09:29 PM
Many thanks PhilipDAth for your response, The two are in separate Data Centers (one per location with no warm spare) but with high availability to allow traffic failover between the two in case of failure on either device. In the current configuration, both are in concentrator mode with the public IP NATed to an internal IP address for each device on a Firewall. Each of the MX 100 is configured with the local IP addresses but the WAN IP address for each is assigned by the NAT configuration on the Firewall. This summarizes the current setup. Thank you
... View more
08-21-2020
04:43 AM
Many thanks guys, A quick clarification: is there any impact to interconnection between the two concentrators (MX 100) if the new public IP addresses are in different subnets ?
... View more
08-19-2020
01:45 AM
Many thanks again PhilipDAth. Sorry to bother you again, I presume the VPN registry is on the controller or is this on the concentrator. Thanks
... View more
08-19-2020
12:48 AM
Many thanks PhilipDAth for the clarification. Do you have an idea about sequence of events for the propagation of the new IP address from the concentrators (MX 100) to the remote devices? Additionally I will also like to know what the impact is if during the upgrade, a change in concentrator priority is required. Many thanks for your help.
... View more
08-18-2020
04:17 PM
Hello Guys, We are planning to upgrade the Concentrator uplinks which involves a change of Service Provider and WAN IP address. As this is the first time this is happening, please I need advise on what to expect in terms of convergence with remote sites. We have about 182 active sites connecting to the concentrators. Many thanks
... View more
