Community Record
9
Posts
0
Kudos
0
Solutions
Badges
May 19 2021
7:35 PM
Hi, I'm working in a trading firm and I've had complaints were my traders are experiencing lag or congestion. Since MX84 doesn't have a rule or group policy settings I'd like to ask if there's a way to view the settings of the Normal policy and if there's a way to change this? I'm asking since the VPN ips always default to this policy and I'd like to check the settings for it. Thanks Device: MX84
... View more
Nov 22 2020
4:51 PM
Hi @DaltonWoolsey I tried that configuration above and my users still can't connect. They're using Windows Home 10, and I we found that they can only connect when they're using Admin accounts from Meraki but unable to when they're only using Users. Thanks
... View more
Mar 20 2020
8:39 AM
WAN1 = 1.1.1.1 WAN2 = 2.2.2.2 Main Subnet = 10.1.1.0/24 VPN Subnet = 10.2.2.0/24 Thanks. although I'd rather not touch the way they connect via vpn (via WAN1) since that woulld mean reconfiguring 80+ users again lol. 3. Make a 2nd rule that allows ANY traffic with source of 10.2.2.0/24 with destination of 0.0.0.0/0 to prefer WAN2. If i apply this only and they still connect via WAN1, would that be fine? That should work. You might also want to make a traffic shaping rule so that "localnet:10.2.2.0/24" is shaped to a per client throughput if you are "full tunneling" your traffic. I'm sorry could you explain "full tunneling? Thanks That should work. You might also want to make a traffic shaping rule so that "localnet:10.2.2.0/24" is shaped to a per client throughput if you are "full tunneling" your traffic.
... View more
Mar 19 2020
7:11 PM
Hi, Is there a way to redirect Client VPN's users to WAN2? Right now, they're connecting via WAN1 and I want to redirect their outgoing internet to WAN2. WAN1 is getting oversubscribed due to the huge influx of WFH users and i want to redirect some of the traffic to WAN2. I'm not sure but is it just via Traffic Shaping and adding my client vpn subnet? Would this cause some assymetrical routing? Thanks
... View more
Mar 13 2020
6:55 AM
thanks. but this also affects my site to site vpn connection as well right? like i.e. they'll have to peer with WAN2 now? thanks
... View more
Mar 9 2020
8:51 PM
Hi, Is it possible to direct remote access VPN connections to WAN2? can't seem to find it any on the settings for client vpn. Thanks
... View more
Feb 16 2020
11:29 PM
Thanks. Although, its not a number of rules, but rather 1 rule where i just continually add in ip addresses. like x.x.x.x/32, y.y.y.y/32, z.z.z.z/32, etc i'm actually concerned since we've been doing this for around 2 + years now and I know there will come a time that the ip addresses entries and urls will cause a slowdown or worse might hang the device and i want to know what is that threshold or what's the next possible step that i should do when that happens. Thanks
... View more
Feb 16 2020
8:02 PM
Hi, I have a Deny rule in my firewall where I block malicious IPs attacking our network. At the same time I also block malicious website from being accessed in our content filtering. I'd like to ask is what is the Maximum number of Ip addresses in Firewall configuration that I can block and the maximum number of websites that I can block as well in Content filtering? And in the case of reaching that maximum number, what do I do next? I'm using MX84 Thanks
... View more
Feb 12 2020
6:10 PM
Hi, Is there a way to restrict Client VPN access in Meraki with different groups? I tried looking but so far what I've seen is one to all i.e. the rule applied applies to all. In my case, I want to separate what IT group can access via VPN over the Business side VPN users. Is there a way to do this via Merak? Thanks
... View more