My recommendation, leave it as an access port. Set your ssid that you want on local lan to bridge mode and don't enter a vlan tag. That should work ... View more

So the quickest way to do what you're looking to do would be to change the SSID you want to be part of the LAN to bridge mode. Do not add a VLAN ID. Everything else will continue to work the same way. If you are going to want to add other VLANs eventually, you are going to want to change that to a trunk, but not required for what you are currently doing. ... View more

The OfficeWiFi will continue to use Meraki NAT. Does your AP use a static IP or DHCP? By changing that to a Trunk you will have to add in the VLAN you want the AP to use for the management IP if you use static, originally VLAN 20. If it's set to DHCP it will try to get an IP from the native VLAN (generally VLAN 1) ... View more

Do you have the switchport set to trunk or access? If you're using a trunk then you need the vlan tagged, if you're using an access port don't add a tag. Do you have the SSID set to layer 3 roaming or bridge mode? ... View more

That doc was what I needed. Thank you ... View more

That's what I was seeing as well. My concern is the link I shared says it's AES-128, and since we have to adhere to PCI requirements, it has to be a minimum AES-256. ... View more

I think I submitted this to feedback about 4 years ago. Maybe one day lol ... View more

Started working for me just now ... View more

I'm trying to create a new SSID on n561 and it's just spinning. Tried to refresh and configure it again and the same issue is happening. ... View more

I think you misunderstood what I was saying. If you run the api call https://api.meraki.com/api/v1/organizations/{orgid}/apiRequests?version=0, you get a recent list of v0 api calls, if you change it to version=1, you get a recent list of v1 api calls. As explained here: https://community.meraki.com/t5/Developers-APIs/Identify-API-v0-usage-the-easy-way-0%EF%B8%8F%E2%83%A3/m-p/150274/thread-id/6006   ... View more

That's what I was hoping, just wanted to make sure I wasn't missing something that I should check.   Thanks ... View more

We are actually replacing a lot of the old copper lines at our remote locations with new desk phones. Gas stations and service shops will probably have desk phones for a long time ... View more

You don't have to run an ethernet connection, but you will need power. If it doesn't have a direct ethernet connection it will Mesh with another AP that it can reach and the traffic will move to another AP wirelessly to reach the internet.    The downside of doing this, if it can only reach one other AP and that one goes down due to power loss, upgrade, other issues then you lose that AP as well.    Here is some documentation on wireless mesh: https://documentation.meraki.com/MR/Wi-Fi_Basics_and_Best_Practices/Wireless_Mesh_Networking   ... View more

We were able to do the upgrade last night, and that did fix the issue, thanks again! ... View more

yep that is our exact issue, we are currently running 3.0. I'll try to get approval to move to 3.101 but may have to wait until it's 'stable'.   Thanks @javalins  ... View more

This is our first site that has the MG. We are using Verizon as the primary carrier on it and AT&T as the backup. We have paid to not have the CG-NAT.    When we ping from outside of that network we can see the pings hit the MX and the MX responds but we don't see the response in the packet capture on the MG.   Data Center -> MG -> MX looks fine but the packet captures only show MX -> nothing coming from the MX on the MG ... View more

Each org can have administrators, as far as I know you can't create 1 account that automatically gets access to all orgs. My setup has 4 Orgs but only 2 people have access to all 4. We also have a few that only have access to 1 org with varying levels of access. So you can be setup to be an org admin for that 1 org, if your company/department allows it. ... View more

Yeah, most of our templates are from around 2019, I just checked that API call and it shows most of ours are appliance and wireless only...   I will say even with the tac case we have open, your slide deck makes so much more sense. I think we may have this figured out today now ... View more

@Ryan_Miles that's a really informative slide deck, we've actually been dealing with this same issue with adding an MG. Any idea why this is so difficult instead of being to just update the current templates to include new devices? ... View more

How did you know I needed this? lol We just tested a MG to replace our cradlepoint/connectedio devices so this is perfect timing ... View more

I'm not great with Python but when i attempt, i'm getting 404 on browser and postman, but I'm also not enrolled in EA. Are all of your networks enrolled in that? It could be something as simple as that.  ... View more