About Johnfnadez

Johnfnadez · ‎07-24-2020

Awesome! Thank you!

Johnfnadez · ‎07-23-2020

IKE versions hava changed, you can check your peers

Johnfnadez · ‎07-22-2020

You can configure a 3rd party vpn with azure in the MX. https://documentation.meraki.com/MX/Site-to-site_VPN/Configuring_Site-to-site_VPN_between_MX_Appliances_in_Different_Organizations It also applies for Azure, AWS and any IPsec peer. I have used for fortinet, Cisco ASA and another MX in different orgs

Johnfnadez · ‎07-21-2020

Yes, I have asked to Meraki Support and the say that I don´t have the requirements for having this feature, but actually I have the MSP portal

Johnfnadez · ‎07-21-2020

I´d like to know that are the requirements to qualify? bc currently I`m administrating around 6 organizations

Johnfnadez · ‎07-14-2020

Hi Merakiers!!! I hope that you are doing well I have a doubt and I haven´t found out something official from Meraki. Let me explain me: I have syslog servers on all my MX around the Country and I have been receiving logs regarding with URLs and the type regarding Meraki es "url" but I´d like to apply a kind of category like Cisco where i have different levels of syslog messages regarding the severity of them... But I don´t know how to remark this kind of log what level do I have to use??

Johnfnadez · ‎06-24-2020

Bienvenida!!

Johnfnadez · ‎06-24-2020

The best option for you es creating a "Configuration template" and then after creating networks with it`s own MX bind the template to the network. https://documentation.meraki.com/zGeneral_Administration/Templates_and_Config_Sync/Managing_Multiple_Networks_with_Configuration_Templates Just take in count the firmware upgrades bc in the future you only will be available to upgrade firmware ussing those templates. The best practice is to divide it into networks that physically are near from each other, just in case that the meraki device does not work fine after upgrading Regards.

Johnfnadez · ‎06-23-2020

No-NAT feature is available in the beta MX

Johnfnadez · ‎06-23-2020

The last friday we enabled web caching feauture in our MX84s. And today I received a case related with issues with a internal site working with HTTP wich was having issues to charge the page... therefore we disabled web caching and It got fixed! So, i´m wondering why is this affecting us and if Meraki Support can perform whitelist rule to avoid caching on this specific site. Regards

Johnfnadez · ‎06-11-2020

Meraki Community has made me a Meraki Guru!

Johnfnadez · ‎06-10-2020

It have gotten fixed without intervention LMAO

Johnfnadez · ‎06-10-2020

Hi Merakiers! I need to apply whitelist rules in my IPS/IDS rules to specific IP, but I cannot have the option and I`m wondering if anyone knows how to do it, bc I`m just seeing the option to whitelist Rules and not IP wich I think that is very unsecure...

Johnfnadez · ‎06-08-2020

I have an alert from my MS saying "Port 25 is not using the same VLAN settings as its connected switchport" but I have the correct VLANs on my trunk ports idk why is this appearing....

Johnfnadez · ‎06-05-2020

I have a situation in my dashboard that i don´t understand... I have the option to no run beta firmwares in my organization... But I`m receiving a mail from meraki saying that my switches will be upgradin... And the firmware that the Dashboard schedule automatically is a firmware that I not an stable release yet...

Johnfnadez · ‎05-25-2020

You can perform this change using the Local Status page! Let me show you a usefull guide! https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/MX_Load_Balancing_and_Flow_Preferences Regards!!

Johnfnadez · ‎05-25-2020

Nop It does not. Actually you can see that each sticker has it`s own MAC and SN. But connecting to the network you can see the same mac address wich belong to one of them. Mac+1 bc it´s connected to the Uplink 1

Johnfnadez · ‎05-25-2020

Hi Merakiers!!! I have been deploying around 120 Meraki Branches and the last week I got a serious issue with was too hard to troubleshoot. I was having issues registering the mx bc I did not saw it online in the dashboard. I tried to see if it had the VPN Tunnels up and I saw that another branch wich is not installed yet was taking up their tunnels. I blink the leds in the MX in the dashboard with another serial number and I saw it blinking. Then I realized that I had those switches with certain conflict so I performed a lab with them and now I`m seeing in the switch that they have the same mac address

Johnfnadez · ‎05-13-2020

I`m in!

Johnfnadez · ‎05-12-2020

Hi sorry I had the solution in front of me. Let me attach it: We have to select in state the option Disabled and we will be able to schedule an out hours schedule.

Johnfnadez · ‎05-12-2020

Hi Merakiers! I have a doubt, I need to schedule a policy in my VLAN to denying internet access after 17:00hrs and re enable it at 9:00hrs the next day. But I just have one scroll button to schedule in the morning or in the afternoon. Any idea??

Johnfnadez · ‎05-12-2020

Hi Merakiers!!! I hope that you are so fine! 🙂 I have a doubt with scheduling a policy. The hours that i`ll put is regarding the network time? or what is the reference? Regards

Johnfnadez · ‎05-07-2020

Hi Merakiers! My customer is requesting the last 8 months logs regarding with security events, but In the event log page I just can download one page. Does anyone know if I can request this information to support or do I have any way to got them?

Johnfnadez · ‎05-04-2020

I think that your best way is checking the capalibities and choose the right MX. https://meraki.cisco.com/lib/pdf/meraki_datasheet_mx.pdf

Johnfnadez · ‎04-30-2020

Hi Merakiers!! I`ve been trying to block intervlan routing in my outbound firewall rules, but if i perform a ping from my computer in 192.168.22.0/24 to 172.16.101.0/24 but ping suceed.

Johnfnadez

Community Record

Badges