Ideally endpoints should connect to access ports but that should not be causing this issue. By default the switches come with trunked ports enabled.    Yes, wireless SSID is on vlan 1. Which is also not ideal but should not be causing problems.   Again this was working fine the way it is.  ... View more

Please, provide more detail information: When did the issue start happening? Sometime in April or early May   Did you perform any network or configuration changes around that time? No   What's the switchport configuration? Default settings: Port status Enabled Type  Trunk Native VLAN 1 Allowed VLANs     all Access policy     Open Link negotiation  Auto negotiate (1 Gbps) RSTP  Enabled (Forwarding) Port schedule     Unscheduled Port isolation    Disabled Trusted DAI Disabled UDLD  Alert only Tags  none PoE   Enabled Port mirroring    Not mirroring traffic   Are all client devices that having issue with the same model, OS, etc.? No, not all. We mostly use Dell Latittude laptops but have Dell desktops as well.   Are there any recent Windows updates? No.   Have you tested updating the Windows OS, drivers etc. to the latest? Manually disconnecting wireless on the machines that have both wired and wireless connected seems to resolve the issue. This goes for desktops as well.   When PCs connected via Wired - when exactly disconnected - when it goes to standby / sleep mode etc.? This is intermittent. We can't think of anything else than the PC is sending traffic on both the wired and wireless interfaces. THe PC is not going in sleep mode. THe user is actively working on the computer and gets disconnected.   Do you see any Event logs for the specific devices? Nothing out of the ordinary.   Have you taken packet captures? Does the PC still have IP address? No, because it's intermittent and we can't reproduce it at will.   When you configure the PC with a Static IP address - does it experience the issue? I haven't thought of that. The PC's obtain DHCP addresses.   Ensure the Meraki switch is running the latest firmware Yes, neither the old nor the new firmware resolved the issue. ... View more

I like your creativity, but this can potentially become quite an ordeal to manage which I would want to avoid.  Just to mention a few, monitoring and zscaler, could make it a mess.   ... View more

As for your gateway question, VLAN 2’s gateway will still be the Meraki switch (let’s say 192.168.2.1). The switch will then decide where to send the traffic—straight to Firewall 2 based on the static route.   How would you do this if a default route is already present on the L3 switch? How would you add another static route pointing to a different gateway for destination 0.0.0.0/0? ... View more

Sorry for some missing information but of course vlan 1 and vlan 2 have unique network ip addresses ranges. I just need to know if it's possible to configure the Meraki L3 to have 1 subnet route through 1 firewall and the other subnet through the other firewall. The firewalls are on a seperate vlan (not vlan 1 or vlan 2).   Not sure if I understood your reply correctly but how would you set the gateway for vlan 2 to the MX 100 if they're both on different vlans? ... View more

THis is the info I was looking for. Thank you much!  ... View more

This is not good especially for the more complex configuration of the MX appliance. Is there really no way we can save the config, move the device to a new network and restore the config? I can imagine many other companies at some point would need to do the same. ... View more

Will the devices we move lose its current configuration?  ... View more

We want to manage each location as a seperate network or site in the dashboard. We assign subnets to sites. Having devices from multiple locations and ip ranges listed in a single site can make things more complicated. ... View more

Sorry we do not have any non Meraki devices in the dashboard.    We have an MX appliance, switches and Access points listed in the network that we would like to split in 2.   I'm not talking about Organization > Configure > Inventory.   I meant the network dropdown when you select a site to manage the devices. ... View more

My mistake, you are correct the MS120 is L2 only but has the interface added for DHCP relay. The other 2 MS250s do have the vlan interface added for routing.   And yes, all ports are in vlan 1.   And I do see a lot of status change spanning tree port activity. ... View more

Can you elaborate what issues to look for specifically? It was already implemented by this person and it seems like it's functioning like normal. I see no errors on the switches and it's not even complaining about ip conflicts. ... View more

Would I have to modify the script each time new networks are added? ... View more

We have sites of various sizes and settings. From small with 1 vlan to large with more than 10 vlans.   Would that leave Dashboard API access as the only other viable option? And is there a sample script with can use and modify for our purpose?   ... View more

I called support and was told it can also be achieved by using Configuration templates or Dashboard API access along with scripts. I would assume this would raise the level of complexity.   ... View more

Change the switches management interface configuration so that it is pointing at the new Internet circuit. It should come back online in the dashboard after this. You should see it checking in from the new public IP address.     Can we change the ip address of the switch after the ISP router's ip address has changed? How will the switch access the internet after the IP change on the ISP router?    Can I change the switch it's management ip locally from the LAN? This is in case I can get access to a machine on the local LAN.     ... View more

I was not able to access my profile so support had to temporarily disable 2fa so I could update my phone #. .  ... View more