Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
- About TEAM-ind
TEAM-ind
Getting noticed
Member since Nov 21, 2017
10-26-2021
Community Record
24
Posts
4
Kudos
0
Solutions
Badges
10-26-2021
03:13 PM
I did replace the batteries even though the sensor indicated batteries were at 100%.
... View more
10-26-2021
03:11 PM
MV12 4.13 MR42 and MR42E was 27.7.1 when the sensor was working properly and never going offline. However is now 28.5 and able to support the MT10 and the MT10 is going offline and online many times a day. Logs show "detected insufficient RSSI from sensor" many times a day. These showed up only after upgrading the firmware on the MRs. Since the previous firmware did not support the MT sensors, I can only assume the sensor was connected to the MV camera previously, and it was working flawlessly. However, now it does not want to do that with the MRs being available...but the MRs don't provide good enough signal to accommodate the sensor, I guess. So my question is, why won't the sensor choose the MV that is four feet away and stay there? Up until October 10th (that is when the MR firmware upgrade occurred) the sensor and been in production for several months and had been online and trouble free the entire time. Now that the MRs are on a firmware that supports the sensor, I can't keep it online. Meraki is sending a replacement MT10, but I am assuming that will do the same thing. We shall see.
... View more
10-26-2021
10:45 AM
I do see in the logs environment that the sensor is connecting to a poorly performing AP. Is there a way to force a sensor to connect to an MV rather than an MR? I know it can use both as a gateway, but apparently it prefers APs. The MV is only four feet away. I am guessing it was always using that until the MR firmware upgrade.
... View more
10-26-2021
10:33 AM
I have an MT10 that goes offline for hours and causes a "red" indicator on the network to which it belongs. I have opened a support case and they emailed me a link to troubleshooting. Very helpful. Does anyone else have an issue with sensors going offline for hours at a time, then coming backing online on their own without any steps taken to resolve? This seemed to start after a recent MR firmware upgrade. I provided this information to support, but they said that is not the issue and do not revert. There is an MV camera about 4 feet from the sensor and the sensor should be using this MV as its gateway. Is there a way to check what the MT sensor is using as a gateway? Is there a log for this connection?
... View more
10-01-2021
08:55 AM
Please post follow up if/when you proceed with 15.44 on the mx400s. I've been holding off on my mx400 HA pair upgrade, due mostly to procrastination. But seeing this discussion, I am glad I procrastinated.
... View more
04-12-2021
06:48 AM
Hmm...I have the issue as well. MS350 and MX400...MX400 throughput indicates 350-400Mb/s, and MS350 says 30Mb/s. If switches don't have the CPU to accurately run the throughput test, that should be noted in the dashboard, I think.
... View more
10-22-2020
06:46 AM
Looks like the order of the switches is determined by MAC address, and not a whole lot a person can do other than make sure they are in the desired physical order in the rack (paying attention to the MAC when racking). Is this correct? I'm trying to reorder in the switch dashboard, myself.
... View more
06-19-2019
12:20 PM
3 Kudos
Older thread here, but I just wanted to post that Meraki supports states that this is fixed in 15.12: "The issue is fixed in 15.12. "Updated the AMP service to more gracefully handle cases where there are many out-of-order packets. This will result in fewer instances of file downloads failing when AMP is enabled." Please upgrade your MX(es) to 15.13 get the fix."" I have not verified this, but thought it worth sharing, anyway.
... View more
12-20-2018
06:35 AM
1 Kudo
Still no fixes for several known AMP issues, even with the latest 15.x that you need a support engineer to push. AMP is not going to be internal application friendly for quite sometime, based upon my experience with our internal SharePoint sites and forms, and a fix still not available in even the lastest beta.
... View more
12-11-2018
11:50 AM
Another update. 15.10 did not fix the AMP issue that I am seeing, and broke port 2 on an MX100 that was configured to use that port as internet 2. Rolled back to firmware 13.33 and port 2 works, again...AMP still has many issues, even with the latest beta, and the latest beta is not a good idea in a production environment. All done now. Thanks.
... View more
12-11-2018
06:30 AM
Upgraded to 15.10, today. After the upgrade, I have no WAN2 connection. Support has verified this happened as a result of the upgrade and is advising to either reset the appliance or roll back the firmware. Just wanted to share are bad experience with beta.
... View more
11-09-2018
02:37 PM
Update on this -- Meraki support says I should "try" 15.10. Anyone tried a version of firmware that requires Meraki Support to push?
... View more
10-26-2018
11:21 AM
Thanks, again MacUserJim for the suggestion. I have stayed away from beta versions as that has always implied "not ready for prime time" to me. But I may have to put that bias away, as it pertains to MX software.
... View more
10-26-2018
09:29 AM
Thanks for the suggestions, MacuserJim. I am at 13.33 on all of the appliances. Still seeing frequent AMP issues related to whitelisting not having any affect. Both on MX100 and MX84.
... View more
10-26-2018
09:04 AM
I have nine locations each with a Meraki MX security appliance. All of the locations use content filtering and group policies to restrict access to certain websites. I am having an issue with internal intranet sites being blocked on a shopfloor policy that blocks all url patterns (*) and only allows patterns on the matching whitelist. I am having to white list are internal URL patterns. Further, AMP is causing issues with our internal sharepoint site at one of our locations, and in AMPs case, the whitelists are not at all reliable (many issues where whitelisting has no affect, and disabling AMP does). Is there a way to tell the MX to not apply content filtering and threat protection to Site-to-Site VPN traffic?
... View more
09-19-2018
08:15 AM
Well, sure they can be downloaded. That's not really what I am after with this discussion. Yes, CWS, Umbrella, and anything that does https inspection would do this just fine. I guess the reason I started a new discussion is because I can allow youtube just fine and dandy by policy (even though is still matches a blocked category). I am wondering why I can't do the same for a specific video URL. If https inspection isn't a requirement for my Allow youtube policy (see picture above) to work, why is it a hurdle when I try to get granular (specific video URLs)?
... View more
09-19-2018
07:57 AM
I have an MX400 and I am using content filtering and categories. I block streaming media, and I have a policy setup up to allow youtube. This policy is applied by LDAP group membership, and it works great. Users that are members of the group can get to youtube, and all other stream media categories are still blocked. I would like to be able to do something similar with specific youtube video urls. The goal is to block youtube by category, but allow a specific URL match within youtube. This does not seem to be doable, and it has been discussed, but it's important enough to my company to warrant a new discussion thread. Anybody else working around this issue?
... View more
01-22-2018
12:40 PM
thanks for the feedback @PhilipDAth. I will have to consider the upgrade. I did check both the IP and URL with BrightCloud, and both are fine. Only the MX is classifying it as malware...just wondering how it's making that decision if it's supposed to get it's marching orders from BrightCloud. I guess it must be a bug in the code.
... View more
01-22-2018
11:24 AM
Thanks for the reply. I am still wondering how often the cache is updated if you are using Top Sites rather than Full. Or am I to understand that Top Sites is no longer supported? I've seen several posts regarding incorrect classes, and a suggestion to go to 13.x. We are an 12.26. It is my understanding 12.26 is the latest stable release. I see the 13 chain is now "stable release candidate" and there is a 14 build in Beta. Is it an error on my side to assume the latest stable release is where I should be?
... View more
01-22-2018
09:27 AM
I am using the "Top Sites only" setting. In this mode, how often does the MX pull the list from BrightCloud?
... View more
01-22-2018
08:14 AM
I have an MX400 with content filtering enabled and we are blocking many categories, including Malware. I am seeing several sites that seem to have errors in classifications and are getting blocked. Most recently: If you feel you have received this message in error, please contact your network operator with the following information: URL: http://www.marclatulippe.com/ManuelShopMotoneige/Polaris/2010-2012%20Polaris.pdf Category: Malware Sites Server: 50.63.202.32:80 BrightCloud's lookup tool returns this URL as a Business and Economy match. What's going on here? The engine the Meraki uses is Bright Cloud, correct?
... View more
01-08-2018
01:23 PM
Support says this is a known issue, and they are working on it. Anyone else seeing it? Is it just the MX100s? Or all security appliances?
... View more
11-21-2017
01:26 PM
Yes. Same here. From all clients I have tried, dashboard is not working with IE.
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 3 | 2847 | |
| 1 | 3387 |
