I'm using Meraki cloud authentication now, but I'll be switching to AD authentication later. I have 2 active directory servers. Is it a good practice to use both servers as NPS (Network Policy Server) or just one? I'm assuming both will be good, but just want some advice.
... View more
I got it figure out. It was a combination of switch and AP setting issue. I made 2 VLANs trunk, and one access. On the UniFi controller I applied VLANs to the SSIDs that I want, and no VLAN for the remaining one. I have a total of 3 SSIDs for each VLAN.
... View more
I made some changes to the Netgear switch. I removed the trunk port, and made it an access port with members of VLANs 2,3,4. PVID is 4. The AP is getting dhcp from VLAN 4, and I'm able to adopt the AP from the UniFi controller. But when I connect to the SSIDs, they say "No Internet"
... View more
What was the issue with VLAN assignment? I’m using a Netgear switch connected to MX. I tried a new UniFi AP same thing. It gets dhcp from switch but can’t ping it from MX dashboard.
... View more
@MerakiGuy90 The UniFi AP is connected to a trunk port which have VLANs 2,3,4. The PVID is 4. So the AP should be getting a VLAN 4 dhcp but its not. When connect a laptop to the same trunk port the laptop gets a VLAN 4 dhcp.
... View more
Checked cable. Replaced cable just in case. Same issue. The AP itself is not getting dhcp. I have different SSIDs connected to different VLANs and they work. Chrome discover can’t find AP unless I change my laptop to 192.168.1.0 subnet. Same as earlier. Just to be clear, everything works, but the AP is not getting IP. I haven’t tried manually assigned an IP.
... View more
UniFi AP AC PRO. This is connected to a Netgear switch trunk port. But its not getting a dhcp. But, if connect a laptop to the same trunk port, the laptop gets dhcp.
... View more
@PhilipDAth This is not a Meraki issue. I'm able to ping the AP. I have the AP working now, but for some reason its keeping the factory default IP. I'm able to connect to the SSIDs based on the VLAN, so I know my switch is correct also. I need to figure out that part. Thanks for the reply.
... View more
Also just to make sure it's not a switch issue, I connected a laptop to the same trunk port on the switch where the AP was connected. The laptop got the correct VLAN dhcp and it's able to access the network, but when I connect the AP it looks like it's getting a dhcp, but I can't ping it. Just wondering if anyone had any experience in dealing with this.
... View more
I'm trying to adopt a UniFi AP, but I'm not able to ping it for some reason. When I login to the Meraki cloud, I can see the MX giving the UniFi a dhcp, but I can't ping it from the Meraki dashboard either. I don't have any firewalls in place. Any ideas why?
... View more
When I was having ISP problem, I connected a Verizon JetPack to a laptop, and I bridged the JetPack and the laptop's NIC card. Then, connected from laptop to the Meraki. I didn't have good experience with this setup. May be a USB modem will work, I used this Verizon Global Modem USB730L
... View more
I'm able to connect to the MX using the client VPN. But when I logged into the dashboard, I'm seeing this "Non-Meraki / Client VPN negotiation" I'm logging into the MX from our current Cisco network. I have different public IPs for the Cisco and Meraki. Is this a normal message? Can I make this go away?
... View more
@kYutobi @jdsilva I got a reply from Meraki support. They said "Devices will appear in the Network-Wide > Clients page if they pass any Internet Traffic. Connectivity for the device will show up, so long as the device is passing traffic. If the device does not pass traffic for more than a minute then it is marked as offline." https://documentation.meraki.com/MR/Monitoring_and_Reporting/Clients_Usage_Page_Overview#Navigating_the_Clients_List
... View more
Yes, I have link lights on the MX, and if I go to tools on the dashboard, I can ping the switch by it's IP address. Could it be because it's a non Meraki switch?
... View more
I have a Netgear connected to the MX. But on dashboard, it's showing as offline. I can ping the switch from MX and the laptop is getting dhcp from the switch, so I know the switch is alive. I tried a different browser and it's showing the same thing.
... View more
//
//
LITHIUM.InformationBox({"updateFeedbackEvent":"LITHIUM:updateAjaxFeedback","componentSelector":"#informationbox_69f8c26a6d1eb0","feedbackSelector":".InfoMessage"});
LITHIUM.InformationBox({"updateFeedbackEvent":"LITHIUM:updateAjaxFeedback","componentSelector":"#informationbox_69f8c26a6d1eb0_0","feedbackSelector":".InfoMessage"});
LITHIUM.InformationBox({"updateFeedbackEvent":"LITHIUM:updateAjaxFeedback","componentSelector":"#informationbox_69f8c26a6d1eb0_1","feedbackSelector":".InfoMessage"});
LITHIUM.InformationBox({"updateFeedbackEvent":"LITHIUM:updateAjaxFeedback","componentSelector":"#informationbox_69f8c26a6d1eb0_2","feedbackSelector":".InfoMessage"});
LITHIUM.AutoComplete({"options":{"autosuggestionAvailableInstructionText":"Auto-suggestions available. Use Up and Down arrow keys to navigate.","triggerTextLength":4,"autocompleteInstructionsSelector":"#autocompleteInstructionsText_69f8c264a3ac2e","updateInputOnSelect":true,"loadingText":"Searching...","emptyText":"No Matches","successText":"Results:","defaultText":"Enter a search word","autosuggestionUnavailableInstructionText":"No suggestions available","disabled":false,"footerContent":[{"scripts":"\n\n;(function($){LITHIUM.Link=function(params){var $doc=$(document);function handler(event){var $link=$(this);var token=$link.data('lia-action-token');if($link.data('lia-ajax')!==true&&token!==undefined){if(event.isPropagationStopped()===false&&event.isImmediatePropagationStopped()===false&&event.isDefaultPrevented()===false){event.stop();var $form=$('