Access point is down due to POE issue , getting 30 watts instead of 40 watts

teja
Comes here often

Access point is down due to POE issue , getting 30 watts instead of 40 watts

Hi fellow meraki users , 

 

i have a access point connected to our switch and it went down , by checking power inline status , it is showing as IEEEPD and also other access points are getting 40 watt power and this one is getting 30 watt power.
Cisco Meraki cw91661  is connected to Te1/0/20 , Could someone let us know what is the exact issue and why AP went down.

 

Gi1/0/11  auto   off        0.0     n/a                 n/a   60.0
Gi1/0/12  auto   on         40.0    Meraki CW9166I Clou 4     60.0
Gi1/0/13  auto   off        0.0     n/a                 n/a   60.0
Gi1/0/14  auto   off        0.0     n/a                 n/a   60.0
Gi1/0/15  auto   on         30.0    Ieee PD             4     60.0
Gi1/0/16  auto   off        0.0     n/a                 n/a   60.0
Te1/0/17  auto   off        0.0     n/a                 n/a   60.0
Te1/0/18  auto   off        0.0     n/a                 n/a   60.0
Te1/0/19  auto   off        0.0     n/a                 n/a   60.0
Te1/0/20  auto   on         30.0    Ieee PD             4     60.0
Te1/0/21  auto   on         40.0    Meraki CW9166I Clou 4     60.0
Te1/0/22  auto   on         40.0    Meraki CW9166I Clou 4     60.0
Te1/0/23  auto   on         40.0    Meraki CW9166I Clou 4     60.0
 
>>>>>>>>>>>>>>
 
NOT ABLE TO SEE IT CDP NEIGHBOURS.
sh cdp nei
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
                  D - Remote, C - CVTA, M - Two-port Mac Relay
 
Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID
JJ-wFF-cS01     Ten 1/1/1         136              S I   WS-C3850- Gig 1/1/3
tGG-wSS-aF03     Ten 1/1/2         126              S I   WS-C3650- Gig 1/1/1
eeesfsffs                Ten 1/0/21        171              R S   Meraki CW Port 0
ssdjjsjs                  Ten 1/0/24        130              R S   Meraki CW Port 0
ddvdvdvfvd0     Ten 1/0/23        122              R S   Meraki CW Port 0
dcvdvfdv55         Gig 1/0/12        130              R S   Meraki CW Port 0
dsdvfvdvf            Ten 1/0/22        178              R S   Meraki CW Port 0
 
 
5 Replies 5
alemabrahao
Kind of a big deal
Kind of a big deal

If the device is only receiving 30W, it may not be receiving enough power for optimal operation.

I suggest you open a support case.

 

alemabrahao_0-1703332913272.png

CW9166 Installation Guide - Cisco Meraki

I am not a Cisco Meraki employee. My suggestions are based on documentation of Meraki best practices and day-to-day experience.

Please, if this post was useful, leave your kudos and mark it as solved.
Amit_pal
Getting noticed

To which platform AP is connected ? i would suggest checking power on the switch if it has enough power for AP

BlakeRichardson
Kind of a big deal
Kind of a big deal

Does the switch have enough POE capacity to support all of the devices plugged into it? 

marce1000
Getting noticed

 

        - Enable LLDP on the involved port(s) ,

 

  M.

UKDanJones
Building a reputation

This is the answer 

Please feel free to hit that kudos button
Get notified when there are additional replies to this discussion.
Welcome to the Meraki Community!
To start contributing, simply sign in with your Cisco account. If you don't yet have a Cisco account, you can sign up.
Labels