No connection to WLC

SOLVED
MarcP
Kind of a big deal

No connection to WLC

Hi,

 

I am using a MX65 in a location and got Cisco AccessPoints (AIR-CAP1602I-E-K9) in use.

 

When I sent an AP (factory defaults) into this location it is getting an IP but not connecting to my WLC here in the headquater. Before using Meraki, we used Cisco Router, where I needed to configure 2 udp forwardings and one helper-address.

If I´m doing the setup before I sent the AP into the location everything works, when it´s connected on-site.

 

As far as I see, udp forwarding is not the solution at Meraki, but I don´t find an solution and the support says I have to get in contact with Cisco, but don´t have a responsible person and also don´t understand what he wants me to do.

Tried it with dhcp option 43 as well, without succes.

 

Has had anyone this problem and solved it? Would be grateful for any kind of help.

 

Thanks,

Marc

1 ACCEPTED SOLUTION
NolanHerring
Kind of a big deal

https://shimi.net/services/opt43/

 

You have your information criss-crossed

 

10.0.1.199 = 0a.00.01.c7 which means option 43 = f1040a0001c7

 

10.0.1.201 = 0a.00.01.c9 which means option 43 = f1040a0001c9

 

So in your case the DHCP option 43 will need to be set to "f1040a0001c9" and hopefully it will start working 😃

Nolan Herring | nolanwifi.com
TwitterLinkedIn

View solution in original post

12 REPLIES 12
ww
Kind of a big deal
Kind of a big deal

did you  make packet captures on the mx lan and wan and maybe looked what is blocked or not responded to. 

MarcP
Kind of a big deal

@ww:No, to be honest didn´t do that so far, but will do that today... But I´ll set up an Test location and do it there...

 

@NolanHerring

 

2018-11-23 08_52_15-DHCP Configuration - Meraki Dashboard.png

rhbirkelund
Kind of a big deal

Try setting the hex value without colons. I.e. f1040a0001c9
LinkedIn ::: https://blog.rhbirkelund.dk/

Like what you see? - Give a Kudo ## Did it answer your question? - Mark it as a Solution 🙂

All code examples are provided as is. Responsibility for Code execution lies solely your own.
NolanHerring
Kind of a big deal

Can you provide a screenshot of how you have Option 43 configured?

Also are you able to provide the console output from the AP after you turn it on.

Might be worth trying to set up the port forwarding via the following guide using these ports. Not sure if this will work though.

https://documentation.meraki.com/MX/NAT_and_Port_Forwarding/Port_Forwarding_and_NAT_Rules_on_the_MX

ip forward-protocol udp 12222
ip forward-protocol udp 12223
ip forward-protocol udp 5246
ip forward-protocol udp 5247
Nolan Herring | nolanwifi.com
TwitterLinkedIn
MarcP
Kind of a big deal

Don´t know why, but in my test location it is working... using my default settings.

 

Does anyone know what the Value stands for? I can´t confirm it is the MAC address of the WLC...

rhbirkelund
Kind of a big deal

Option 43 is not the mac address of the WLC.

It is the IP address of the WLC in Hex format.

 

See Cisco's document on option 43 

https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/97066-dhcp-option-43-...

 

LinkedIn ::: https://blog.rhbirkelund.dk/

Like what you see? - Give a Kudo ## Did it answer your question? - Mark it as a Solution 🙂

All code examples are provided as is. Responsibility for Code execution lies solely your own.
NolanHerring
Kind of a big deal

Give me the IP of your WLC and I can convert it to the correct hex format
Nolan Herring | nolanwifi.com
TwitterLinkedIn
MarcP
Kind of a big deal

Old is 10.0.1.199 --> f1:04:0a:00:01:c9

New is 10.0.1.201 --> ?? can´t convert it to the correct format, always getting: "0a0001c7"

 

Can you provide an webpage?

rhbirkelund
Kind of a big deal

TLV values for the Option 43 suboption: Type + Length + Value. Type is always the suboption code 0xf1. Length is the number of controller management IP addresses times 4 in hex. Value is the IP address of the controller listed sequentially in hex. For example, suppose there are two controllers with management interface IP addresses, 192.168.10.5 and 192.168.10.20. The type is 0xf1. The length is 2 * 4 = 8 = 0x08. The IP addresses translates to c0a80a05 (192.168.10.5) and c0a80a14 (192.168.10.20). When the string is assembled, it yields f108c0a80a05c0a80a14. The Cisco IOS command that is added to the DHCP scope is option 43 hex f108c0a80a05c0a80a14.

 [link]

 

In your case;

Type: 0xf1

Length: 0x04

Value: 0x0a.0x00.0x01.0xc9

 

Therefore; f1040a0001c9

LinkedIn ::: https://blog.rhbirkelund.dk/

Like what you see? - Give a Kudo ## Did it answer your question? - Mark it as a Solution 🙂

All code examples are provided as is. Responsibility for Code execution lies solely your own.
NolanHerring
Kind of a big deal

https://shimi.net/services/opt43/

 

You have your information criss-crossed

 

10.0.1.199 = 0a.00.01.c7 which means option 43 = f1040a0001c7

 

10.0.1.201 = 0a.00.01.c9 which means option 43 = f1040a0001c9

 

So in your case the DHCP option 43 will need to be set to "f1040a0001c9" and hopefully it will start working 😃

Nolan Herring | nolanwifi.com
TwitterLinkedIn

 


@NolanHerring wrote:

https://shimi.net/services/opt43/

 

 


Awesome link; hereby bookmarked. 🙂

LinkedIn ::: https://blog.rhbirkelund.dk/

Like what you see? - Give a Kudo ## Did it answer your question? - Mark it as a Solution 🙂

All code examples are provided as is. Responsibility for Code execution lies solely your own.
MarcP
Kind of a big deal

Thanks all for your help, its works now 🙂

Get notified when there are additional replies to this discussion.
Welcome to the Meraki Community!
To start contributing, simply sign in with your Cisco account. If you don't yet have a Cisco account, you can sign up.
Labels