Community Record
62
Posts
7
Kudos
0
Solutions
Badges
Thanks for your reply. The switch is connected to firewall. On the firewall side, we often can see the interface disconnection for several seconds each time from firewall log file. so we want to see if there is disconnection on the switch log file. but now we cannot find the log file for the switch. As the disconnection time is too short, maybe it is hard to find the info.
... View more
Thanks for your reply. The switch is connected to firewall. On the firewall side, we often can see the interface disconnection for several seconds each time from firewall log file. so we want to see if there is disconnection on the switch log file. but now we cannot find the log file for the switch. As the disconnection time is too short, maybe it is hard to find the info.
... View more
Hi Please see the below screenshot. It looks like we only have four choices to check the historical data. If we want to check specific one hour of Historical data of past last month, is it possible? Or can we get the exact info like cisco log. thank you
... View more
Oct 28 2019
8:14 AM
@BrechtSchamp at the same time point, do not know why it has two different color green and gray? please see the below above is Historical data for the last 2 hours
... View more
Oct 24 2019
1:40 PM
the cable is running well now so we cannot get some error info at this moment but when checking status history, why it show non color on this box on two hours? please see the below screenshot and what is that meaning "Could also be the device has Energy-Efficient Ethernet (EEE)" ?
... View more
Oct 24 2019
9:32 AM
Yes you are right. I guess it is cable issue and needs to be replaced. please see the screenshot. any other can cause the issue? thanks
... View more
Oct 24 2019
8:57 AM
Hi at Switch MS120-48, one port is disconnected sometimes. when we try to run packet capture, it shows some ip address there. can anyone tell where the ip address is coming from? please see the screenshot attached. Thank you
... View more
Excellent explanation!
... View more
Thank you so much for your reply. How can we know which switch is root?
... View more
Hi there are three meraki switches A, B and C with full connection for each one. My question is whether there is the same spanning tree mechanism as Cisco general switch? for example, If switch A is root, and port at switch B connected to switch A is designate port, the port at switch C connected to A would be blocked? Thank you
... View more
May 20 2019
11:31 AM
Thank you for your reply. If PC and ip phone are connected to the same port, i would see the two mac address based on what you said. From there, can i know which mac is from PC or IP phone?
... View more
May 20 2019
6:29 AM
Hi Please see the below picture, which is from switch summary. I would like to know whose mac is there? Is it PC's mac or ip phone mac? If PC and ip phone are all connected to the same port, can we see the two mac address there? thank you!
... View more
May 15 2019
7:39 AM
1 Kudo
Thank you!! That means we can put ip phone and pc mac in "Whilelisted MAC" window box together, right?
... View more
May 15 2019
7:30 AM
Hi Merakia switch port is connected to ip phone and PC. the access policy is open. My question is when i add ip phone mac to the access policy, do i have to add the pc mac address? thank you
... View more
Apr 25 2019
1:48 PM
Hi There are a lot commands which can show Qos status for Cisco switch. How to know Qos status in Meraki Switch? thank you
... View more
Apr 25 2019
7:37 AM
i think you are right. I found the below when go to Switch ---> switch setting ---> Qos. QoS rules based on port ranges are not supported on the following switch models in your network: MS120. Highlighted rules below are not supported and will be omitted by the following switches: And another question is by default switch port can recognize voice traffic(ef) and treat it as it is if th port is connected to phone?
... View more
Apr 25 2019
7:07 AM
Hi Looks like not all Merakia switch support Qos. Anyone can tell which model support Qos or not? thank you
... View more
Apr 24 2019
1:52 PM
select switch > Scroll to Clients. I could not find the "Clients", maybe i just check at different page
... View more
Apr 24 2019
9:47 AM
Hi In cisco, we can see device mac address by command " show mac address-table". Do we have the equivalent in Merakia switch? Thank you
... View more
Apr 11 2019
6:43 AM
the orange status is not for switch port, it is for the switch. please see the below:
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 1 | 2918 | |
| 1 | 3372 | |
| 1 | 3595 | |
| 1 | 6718 | |
| 1 | 6272 |
