Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Become a member of the Cisco Meraki Community today
Get answers from our community of experts in record time.
Join now- About Unexus
About Unexus
Unexus
Here to help
Member since Jan 23, 2023
a month ago
Community Record
14
Posts
7
Kudos
1
Solution
Badges
a month ago
2 Kudos
After disabled Thread Protection the speed increased to the max. ReEnabling it drops the speed again to 200-400Mbps. Explaned by the supportdesk as well.
... View more
Mar 2 2025
11:48 PM
2 Kudos
Figured out it works when you change DNS entries on the WAN side via <localip>/#configure screen. Sounds like a bug to me that changes are not applied via the cloud portal.
... View more
Mar 2 2025
6:39 AM
The speedtest I run is provided by my ISP. When I run this one directly on the WAN connection (MX67 replaced by a laptop) I measure around 1Gbps constantly. When the laptop is replaced by the MX67 I measure once 700Mbps, then constantly around 200Mbps. No Group policies and/or traffic shaping per client enabled. The last one is set to unlimited. I will investigate the VPN's whether they are influencing the speed I see Cisco mentions a Maximum VPN Throughput of 400Mbps, so what does this mean for the WAN interface, will it drop to a lower rate due to VPN's that also run over it? Do I have to separete WAN and VPN traffic, e.g. VPN traffic over WAN2 and plain internet over WAN1?
... View more
Mar 2 2025
4:56 AM
2 Kudos
The DNS IP's are for my connection, provided by the ISP. As you can see from the screenshot I am able to use them for DNS lookup
... View more
Mar 1 2025
11:28 PM
Running MX67 with latest stable firmware DNS changes in WAN1 are not saved. I have a new ISP and want to change the IP4 DNS values on the WAN1 side. Currently they are 8.8.8.8 and 1.1.1.1. I follow the next steps: Sec & SD WAN > Appliance Status Uplink in the top menu Edit WAN Change DNS1/2 to 89.20.160.228/89.20.160.229 Pressing Update > Loading appears Back to the Applicance Status. Still the old values are shown Uplink in the top menu again This shows the new values Back to Appliance status shows the old values Click on Network Wide > Clients and back to Sec & SD WAN > Appliance status Click again on Uplink in the top menu Edit WAN1 > Shows the old values so new values are not saved.
... View more
Mar 1 2025
11:24 PM
MX67 on latest stable version MX 18.211.5.1 We have a new ISP with 1Gbps link We connect CAT6A to the ISP CPE device Using static IPV4 provided by ISP on WAN1 P3 connected a laptop on VLAN1 192.168.1.0/24 DHCP When nothing else connected, just this laptop I do a speedtest provided by the ISP just after a cold boot (power disconnect/reconnect). This speedtest shows approx 700Mbps, the limit of the MX67. So far so good. Running another speedtest random after the first one I only get values around 200Mpbs. What is cauasing this? The WAN port shows hovering over 1GBps Auto Negotiate (as the ISP also tells us to configure our WAN port). The LAN port P3 also show 1Gbps Auto Negotiate. When I program the laptop NIC with another static IP the ISP provides in a subnet an connect it directly to the CPE i constantly run approx 900-1000Mbps with speedtests. So my conclusion the MX67 is causing an issue on the WAN speed. We also run 2 site-to-site VPNs over this WAN connection. Can this cause the issue of dropping speed?
... View more
Mar 18 2024
9:36 AM
I would like to block network acess after a device tried to acces a site that gives a postive match on blocked sites/content. E.g. by release the DHCP and only give access after an admin gave consent again. Is such functionality available for MX67? And how to confgure?
... View more
Dec 27 2023
10:28 AM
I have a MX67 Site-to-Site VPN to Azure VPN VLAN1 192.168.1.0/24 When connected with remote client I can connect over Azure VPN to 192.168.1.x (MX67) and another HTTP(S) accessibel device in the local network. In VLAN1 also a SOPHOS RED is connected, that creates a VPN tunnel to another site (192.168.70.0) Connection to 192.168.70.0 is created via a static route via 192.168.1.1 When in local LAN we can connect to 192.168.70.0 (route table in MX shows 192.168.1.1 as next hop) When remote we cannot connect ot 192.168.70.0 anymore. Traffic gets lost somewhre in MX. When we make a wireshark trace in MX, we see trafic coming from Azure VPN clients to 192.168.70.0 but then no further traffice anymore. I expect I need to make a route FROM Azure VPN Clients (10.99.2.0) to 192.168.70.0 via 192.168.1.1 but cannot figure out where to create that. Anyone a suggestion? Regards, Frederik
... View more
Jun 28 2023
7:36 AM
Exactly my road to follow, at least you don't answer with "no, not possible", so it implies its a matter of configuring correct. Right?
... View more
We will get a MS120-48 switch. One port will connect to our MX67 LAN port. Other ports will be patched to outlets On the outlets we want to connect on some ports an unmanaged (Netgear) switch, since the amount of outlets in the office is not enough to serve all the equipment. 1) how can this be done, what do I need to configure on the specific port on the MS120-48? 2) is there a max amount of devices that can be managed on the MS120-48 port? New (and learning on the job) on switching. Frederik
... View more
Apr 11 2023
9:41 AM
Hi, we're moving over to a MX67 and I'm busy with the configuration. I have 2 WAN connections both connected and up, first on WAN port, second on Port 2, configured for WAN 2 LAN's I have only port 5 connected, clients are given IP's in range 192.168.2.0/24 via DHCP Uplink is configured as Primary WAN1, Load balancing is disabled and I have dedictated Flow Preferences for ANY 192.168.2.0/24 to ANY 0.0.0.0/32 to use uplink WAN2. I see WAN1 is used (via check MyIP on internet) so I wonder why. I also see in Appliance Status that WAN1 is Active and WAN2 is Ready. When I unplug WAN1, then trafice is routed over WAN2 to the internet. Any idea what I configure the wrong way? Do I forget someting? Is my Flow Pref wrong? The only thing I can think of is that in the VLAN config the uplink is set to Any but when configuring the IPv4 VLAN I never had the option to choose a certain WAN as uplink.
... View more
Mar 31 2023
6:14 AM
Hi, we're moving over to a MX67 and I'm busy with the configuration. I have 1 internet connection with WAN 5 IP's available. 2 LAN's I would like to have something that is called in our current router a WAN IP Alias, 1 phyiscal IP connection, 1 static WAN IP address configured and a few static IP Aliases. Goal: Traffic from LAN1 to the internet is identified on the internet with WAN IP1 Traffic from LAN2 to the internet is identified on the internet with WAN IP2 Is this possible with the MX67 and if so, how? Or do I need to use one of the LAN ports, switch it to WAN and connect my internet via a switch to Meraki WAN1 and WAN2? Regards, Frederik
... View more
Labels:
- Labels:
-
Other
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 316 | Mar 2 2025 11:48 PM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 2 | 340 | |
| 2 | 316 | |
| 2 | 442 | |
| 1 | 1169 |
© 2025 Cisco Systems, Inc.
