Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About Windo
Windo
Comes here often
Member since Mar 7, 2022
3 weeks ago
Community Record
8
Posts
0
Kudos
0
Solutions
Badges
Jan 31 2024
2:04 PM
Just an update that we got this sorted yesterday. a cable wasn't patched in the server room. Once we got it patched the office IT guy set a specific port on the public-facing WAN router. Did have issues with the PPPoE config not connecting until we put it on the office public WAN to update the firmware to 18.107.8 and after a factory reset it connected. All is good now
... View more
Jan 29 2024
11:39 AM
Unfortunately, I don't have direct access to the Wan provider, only the four active ports (13-16). I was under the assumption that one of these would be the PPPoE port. Unless I've got this wrong, either way I'll be chasing the Office IT support
... View more
Jan 29 2024
10:24 AM
Hi thanks for replying, I did get the MX connected briefly before when testing a SIM card but I've removed that now. The firmware shows 18.107.2 We have four active ports in the office and they connect straight away with ethernet on 192.168.60.x range. Should it connect like that if there's PPPoPE setup, seems like something is off. I've reached out to the office IT support but trying to get this sorted while I wait for a reply back from them.
... View more
Jan 29 2024
9:50 AM
My company is setting up an office in Rotterdam which provides Private VLAN via PPPoE. I've connected an ethernet cable to WAN Port 1 and using another Laptop to access the MX Local Status Page; Set it to PPPoE; added the username and password but it's not reaching the cloud. I rebooted the MX a few times and it goes through rainbow colors the status light stays orange. My main Laptop is connected via ethernet and I get 192.168.60.31 IP while the Gateway / DHCP shows as 192.168.60.254 and DNS 8.8.8.8 / 1.1.1.1 Can I get some help with this, please? my brain has gone down the drain.
... View more
Labels:
- Labels:
-
Firewall
Jul 31 2023
9:12 AM
Thanks for the replies gents, we would be just using it as a failover line for our warm spare MX.
... View more
Jul 19 2023
3:14 AM
Hi All, We have 2x MX95 in our Munich office and we use Colt for Primary WAN but I'd like to connect a Telekom Speedbox for the Warm Spare as we can't get any other cabling to our floor. Telekom Speedbox - the mobile router to take with you | Telekom Business Customers The ZTE HyperBox 5G (MC801A ) might be an alternative instead. Would these devices provide WAN to MX95 without any issues? Thanks.
... View more
Dec 12 2022
6:22 AM
Hey everyone, we have an MX105 and want to use AnyConnect so a special group of users can connect to some VMs on our vSphere Server. We've configured AnyConnect to use 10.16.0.0/24 subnet and I've mapped psychical port 2 of the server to a separate virtual switch. The goal is to make sure AnyConnect clients can't access our internal network and only have access to the internet. Any idea where I should connect the dots....my networking brain has completely shut down today...
... View more
Labels:
- Labels:
-
Client VPN
-
Firewall
Mar 7 2022
3:47 AM
Wow long time lurker, finally sign up to see what was going on here, our node n308 is down too.
... View more
© 2024 Cisco Systems, Inc.
