Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About newnovice
newnovice
Conversationalist
Member since Nov 23, 2021
Dec 5 2023
Community Record
12
Posts
0
Kudos
0
Solutions
Badges
Dec 4 2023
11:11 PM
Hi all, Just wondering if I make MS switch L3 routing enabled, using SVI interface for vlan100 like 192.168.100.10, routing deafult gw 192.168.100.1, and make one switch port to access port vlan100, then connect this port to uplink default gw(access port vlan100), and use LAN IP/Management IP:192.168.100.200 gw:192.168.100.1 vlan:blank, Since management ip subnet overlap with its own L3 interce subnet, would this be ok? And should I change the Management VLAN in Configure->Switching settings to 100? Thanks.
... View more
Labels:
- Labels:
-
Interfaces
-
Layer 3
Jun 25 2023
7:36 AM
Hi @alemabrahao, Could you specify how to downgrade the version? Since we got first version 18.107.2, there is no rollback option in dashboard. Must it be done through Meraki Support? Thanks.
... View more
Jun 21 2023
6:59 AM
We have an issue about RDP connection. The client originally used TP-Link c64 router, and only set up static wan ip and DHCP for internal LAN, no other special settings. After that, we replace it with MX67(18.107.2), using the same wan ip address and internal LAN(single LAN). The firewall and L7 firewall are all default. No forwarding rules, content filtering, and AMP, IDP are all disable. We got feedback from client that they use non-standard RDP port(not port 3389) to connect to remote machine. The connection can be established successfully but interrupted about few mins. And client claimed there was no interruption when using c64 router. We captured the packet from WAN and LAN. In part of LAN, we observed the client host only used one TCP high random source port 'T' and one UDP high random source port 'U' to remote non 3389 port 'R'. But in part of WAN, there were lots of UDP packet sent from remote machine with source port 'R' to many different high random destination port besides 'U'. And remote machine sent TCP spurious retransmission packet every few seconds to client host destination port 'T', and client host reply TCP Dup ACK subsequently. Does anyone know what might be the reason causing this?
... View more
Mar 29 2023
2:32 AM
On ethernet tab, what configuration was applied? Enable status? Link negotiation? All of them are enable and auto.
... View more
Mar 29 2023
12:12 AM
On local status page, configure tab, there is uplink(internet) configuration which is don't use vlan tagging, but we capture the packet from Lan Interface.
... View more
Mar 28 2023
7:39 PM
Yes,it was done by dashboard. So even on egress traffic may show an 802.1q VLAN tag?
... View more
Mar 28 2023
7:10 PM
Yes, local status page shows: Internet->This security appliance is connected to the Internet. Cisco Meraki cloud->this security appliance is successfully connected to the Cisco Meraki cloud. The dashboard shows config 'Up to date'
... View more
Mar 28 2023
6:24 PM
Hi there, We have MX250 with firmware 17.10.2, and find out even though we set per-port vlan with Lan port type 'Access', the meraki still send out packet with 802.1Q tag, is it normal? thank you guys. 10.60.34.254 is MX VLAN IP
... View more
Feb 23 2023
12:40 AM
deleted for wrong reply.
... View more
Dec 25 2022
10:20 PM
Hi there, Does MX support PPPoE relay in route mode if client on LAN-side dial-up a pppoe connection? Thank you.
... View more
Dec 28 2021
11:06 PM
Hi all, as subject title, if we add deny any any rule in Layer 3 firewall, does Meraki auto VPN can still be established successfully? Thank you in advance.
... View more
Nov 23 2021
6:54 PM
It looks like meraki using whitelist and block all inbound traffic by default, all you can do is put allowed IP in allowed remote IPs column, on the other hand, if you allowed any, try blocking specific IP by using outgoing rules, or open cases for meraki support.
... View more
© 2024 Cisco Systems, Inc.
