- About NeilB
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
NeilB
Here to help
Member since Apr 9, 2018
2 weeks ago
Community Record
11
Posts
2
Kudos
0
Solutions
Badges
2 weeks ago
1 Kudo
Hi All, Thanks for the posts. It does seem to be all fine with the mix between /24 and /28's. I guess as you are unable to make a full /24 from a subnet that has a /28 already assigned, the dashboard will just issue the /28's from the remaining subnets that can't be used to make the /24s.
... View more
2 weeks ago
Hi, We currently have a number of different deployment templates for the MX's we have in our estate, and we have each template to assign a number of unique /24 subnets from a /16 subnet for each VLAN. We are looking at deploying some Z3 devices which obviously a /24 subnet for 3 VLANs for example is way over the top. What i'm wondering is, if we are wanting to deploy an additional template for the Z3 devices only with /28 subnets for each vlan from the same /16 range as the other templates above, will this cause issues for any subsequent /24 range that will be issued for the non z3 templates? e.g. Non Z3 Template VLAN100 - 10.0.0.0/24 VLAN200 - 10.0.1.0/24 VLAN300 - 10.0.2.0/24 Z3 Template VLAN100 - 10.0.3.0/28 VLAN200 - 10.0.3.16/28 VLAN300 - 10.0.3.32/28 Is the Subnet issuing smart enough to realize that the 10.0.3.0/24 subnet is partially assigned? Hope that makes sense and sorry if this sounds stupid. Cheers Neil
... View more
10-12-2018
12:52 AM
Ah, Thanks for testing. That is interesting. That will cause some issues for us. We don't use the same template for both stack types as we have some non meraki switches that we have at some sites that require more ports than on the back of the MX65's, however we have some smaller sites that, the amount of ports available on the 65's are sufficient, so need to enable all the ports as access ports.
... View more
10-11-2018
08:40 AM
Hi, They are using the same /14 range for both template types. the only difference between the templates is due to us using MX65's where some sites have switches and some just use the local ports depending on the size of the site and how many ports are required. Cheers
... View more
10-11-2018
03:04 AM
Hi, We have a number of templates setup in our dashboard to manage different site types for the MX's we have. As part of the templates, we issue out subnets for each VLAN. I just have a question about, if we change a network to be bound by a different template, will it just continue with the current Subnets it has been assigned initially, or will they be issued new ranges? Sorry if this is a silly question, just wanted to be sure before i move a network over though. Cheers Neil
... View more
09-18-2018
03:42 AM
Ah i thought it flashed green to say it was performing an upgrade. I did manage to get it working previously with a Cisco 1GB copper SFP connected and that worked fine, now i'm just plugging back into port 1. Will try again with an SFP and see if that makes any difference.
... View more
09-18-2018
02:11 AM
The local status page initially says its connected, then after about 5 mins is reporting unable to connect. :S I did notice that it was trying upgrade and was at 37%, but none of the lights indicated that it was upgrading. Yeah i tried turning spanning tree off as i was thinking the same that it was shutting the port down, but no joy. :(
... View more
09-18-2018
01:40 AM
Morning all, I'm having some issues with connecting a MS 8Port switch to my BT Home Hub 5. Initially it connects successfully and reports all fine on the dashboard, however after approx 5 mins, the orange light appears on the front and it drops into offline. It doesn't show on the home hub as a connected device either. :S I can't see any reason for it as i have had it working before. Has anybody else seen this before? Cheers Neil
... View more
09-14-2018
07:09 AM
1 Kudo
I'd like to see it, just to be able to get statistics from the api, so we can monitor usage to ensure that we don't run into any issues with full scopes.
... View more
05-31-2018
03:49 AM
I was just wondering if Meraki had this on the cards for the near future? essentially just a timeout value on the mac address learnt for each port to say 15 mins.
... View more
04-26-2018
06:14 AM
I did as MRCUR said and contacted our Rep. All enabled within a day. Handy tool to use. Noticed there are still some latency issues when adding some filters, but it is still in Beta, so not really that bothered overall.
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 1 | 25 | |
| 1 | 1297 |
