Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About The_Livingstone
The_Livingstone
Here to help
Member since Feb 15, 2018
Mar 14 2019
Community Record
15
Posts
2
Kudos
0
Solutions
Badges
Mar 5 2019
5:51 AM
Hi all , I am still yet to get through with the setup. Can someone advise
... View more
Mar 5 2019
1:03 AM
Phase 1 crypto isakmp policy 20 encr aes 256 authentication pre-share group 5 lifetime 28800 crypto ipsec transform-set eTransform esp-3des esp-sha-hmac crypto map EMSA_NBI 1 ipsec-isakmp set peer x.x.x.x set security-association lifetime seconds 86400 set transform-set ETransform match address IPSECVPN acl ip access-list extended IPSECVPN permit ip 192.168.0.0 0.0.0.255 10.10.11.0 0.0.0.255
... View more
Mar 5 2019
12:08 AM
Dear all, Is their anyone who has successfully setup a VPN tunnel between a cisco router and MX. I seem not to have a break through. Phase one is coming up but phase 2 its not. Please share if their is any work around.
... View more
Mar 4 2019
12:52 AM
I have been having i think similar issues when building vpn between a cisco router and the meraki MX. Phase 1 is up. Phase 2 is okay. I tend to think its the ACL limiting this, since from Cisco router am not natting the subnet to the vpn. But i think Meraki is natting LAN VPN traffic. With the new No-NAT mode, i am i able to exclude the subnet from being natted to a specific destination?
... View more
Oct 11 2018
10:02 PM
Hi Philip, for the purposes of extra public IP, floated through the P2P IPs, BGP will be fine for the IPs to failover
... View more
Sep 25 2018
1:28 PM
Hi Philip, Thanks for the information, i will open a case. For my case i was looking forward for eBGP
... View more
Sep 25 2018
12:07 PM
I would like to know if BGP is fully supported on MX, I have gone through the Meraki documentation and it addresses the VPN setup. Share some insights
... View more
Sep 19 2018
12:54 AM
1 Kudo
Hi Team, From the MX 64-68 overview, it is recommended for 50 clients. Does this mean if i have an office of 80 employees and assuming each has 2 devices which is 160 clients, that the MX64-68 would not be able to support the clients?
... View more
Jun 14 2018
2:48 AM
1 Kudo
Thanks for your reply. I figured out on how to enable ICMP. I went to firewall,
... View more
Feb 15 2018
5:53 AM
hi @Mr_IT_Guy thanks for your feedback, my case is a bit different, am configuring an MX64, i have configured the internet interface with static IP. Interface 4 i have set it to internet and dhcp. when i connect my laptop to the internet port and assign myself the IP on the network, i cant ping the statically assigned IP. also on the monitor i only see the DHCP IP assigned to the interface 4
... View more
Feb 15 2018
5:39 AM
Hi team, How do you verify from the dashboard, that the Static IP assigned has picked
... View more
Feb 15 2018
1:17 AM
Hi Philip, Thanks for the feedback, This is my first time on Meraki Devices, in my case, i have one uplink link to ISP, 2 MX and 2 MS. This is to achieve redundancy incase their is a hardware failure. Could you advice the best setup to achieve it
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 1 | 11925 | |
| 1 | 43085 |
© 2025 Cisco Systems, Inc.
