Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About Mikeylad
Mikeylad
Here to help
Member since Aug 24, 2020
Jul 18 2023
Community Record
17
Posts
5
Kudos
0
Solutions
Badges
Jul 18 2023
4:36 AM
2 Kudos
Yeah the buttons are working again this morning! thanks all
... View more
Jul 17 2023
6:45 PM
Hey guys. what about MX100s? Have they dropped off these charts now?
... View more
Jul 17 2023
6:35 PM
Yeah actually i see that too on the feedback button... broken buttons at the bottom on all our PDL clients. Did you actually log the issue with support or did they add the devices and close your ticket? Support also could add my devices, but as they where adding to Test/DEV org for a customer I left the ticket open hoping it hits the radar of someone able to fix the webpage issue going forward. On a side note another engineer on my team is going to try to add the SNs via API to a PDL customer.
... View more
Jul 17 2023
1:33 PM
I'm glad that im not going crazy... currently on with support again trying to escalate. my ticket for reference is 10467168. I can add the devices to regular licensed customers but not to any PDL - the web page is clearly broken
... View more
Jul 17 2023
12:57 PM
One thing i will point out is that it appears to ONLY be an issue on organizations that are "per device licensing" and it doesn't matter if its a license or a device i try to add.
... View more
Jul 17 2023
9:44 AM
Yes sir, The button changes from a greyed out blue to a deep blue when the full serial is entered - however the next button doesn't work. its just not clickable to move onto the next page.
... View more
Jul 17 2023
6:13 AM
Hey RaphaeIL, Correct - no errors at all just an unclickable blue 'Next' button Ticket opened with support but no replies as yet
... View more
Jul 17 2023
5:59 AM
We are having a strange issue this morning where I cant add any devices to any org. Going to the org Inventory page and then clicking claim, type out the SN or order number and the next button doesn't work - is anyone else having this issue? I've tried different browsers and incognito mode, different orgs etc but I still have the same issue even with different device SNs. Thanks Mike
... View more
Labels:
- Labels:
-
Inventory
Nov 23 2021
7:09 PM
if your configuring at home: from your LAN side of your home router connect it to the WAN/Internet side of your MX. let it check in (white light) and then complete any firmware download (flashing white). Then if your setting up a static IP on the internet port, connect a laptop to the LAN side of the MX and do an IPCONFIG in windows. Open a browser to that IP and log in using the serial number as the login info. Once logged in set your static is on internet the internet port / secondary port at needed. That’s it (with our adding it to the network in the dashboard in question) As long as the MX can get the the internet at the site the rest of the config will sync when you remove the old mx and add the the new one from the network. it’s really quite simple, as mentioned in my previous post - my only issue in the past has been the static IP not taking on the local config, I always double check these days and not ram into any issues.
... View more
Nov 22 2021
5:37 PM
1 Kudo
speaking 1st hand as I've done this many time now: No it does not, it will keep working for a while. When setting up - I like to boot the new appliance on a plain DHCP connection with internet access, get it to check in and let it do all of its firmware updates then plan my outage window (without adding to the dash other than claiming). Configure its static isp info from on local admin page then just ship it to site, let the local person do the cable swap and power up, remove the live appliance from the dash and add the new one from inventory. takes about 5-10 mins tops... One thing I will say is check that your static IP info actually saves after a reboot before you ship and check in different browsers. I did one once which for some reason looked like its static IP was on its internet interface - but ultimately wasn't when it booted at the other end. I always check that twice now.
... View more
Sep 10 2021
7:38 PM
Might not be relevant - But don't forget that depending on your environment: AT&T require one of their modems / routers (on both xDSL and yes Fiber) to authenticate to bring the IP layer up. If your have taken away the PE device - reconnect it and go into the GUI and set your mx as the passthrough.
... View more
Sep 10 2021
4:04 PM
https://community.meraki.com/t5/Security-SD-WAN/Client-VPN-Authentication-on-n109-failing-using-Meraki-auth/m-p/128807#M32047 Check out my post. Im having the issue where users cant authenticate using cloud auth.
... View more
Aug 26 2020
7:29 AM
Good Idea CptnCrrnch, Do you know if that method will retain Vlan and static route configs etc on the dashboard under "addressing & Vlans"? Thanking you!
... View more
Aug 24 2020
3:13 PM
Thanks for the link jdsilva, I've already looked at this before posting but doesn't really tell me anything what happens to the switch and AP configs. As mentioned in my original post - if i clone the network to perform the upgrade - what happens to my switches and APs when they are moved to the clone. Do their configs clear or what? Or would it just be easier to clone just the security appliance and keep the switches and APs on their original network?
... View more
Aug 24 2020
6:33 AM
Hey All, Sorry if this has been discussed before but im not having much luck finding something along the same lines. I have a network that has a MX64, 3 Switches and 18 APs. We are upgrading the MX64 in that network to an MX100. The current MX64 acts as a gateway, VPN gateway and has several static routes pointing to other networks on the WAN and then about 10 local VLANS. The question is this: Looking at the official guides, the best way is to create a new network and clone the current live one. If I do this what happens to my switches and APs when brought over to the cloned network - do their vlan configs get deleted? OR If i cloned the network and just select Security appliance only - would that work. Leaving me with essentially 2 network, one with the Security appliance the other with the switches and APs? I guess what im trying to figure out is - whats the most simple way of doing the swap without loosing configs and having a nightmare? Thanks in advance for any guidance. Mike
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 2 | 4259 | |
| 1 | 3782 |
© 2025 Cisco Systems, Inc.
