Meraki

Community
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 

About dubbs

Re: MX67C-NA Internal SIM Issues

by in Security & SD-WAN
‎Mar 25 2021 6:50 AM
1 Kudo
‎Mar 25 2021 6:50 AM
1 Kudo
When i was going through this, i requested that they hard code the APN on the back end, which never really worked. Try requesting the hard coded APN be removed from their side. I had to do this as well. Then try the rebooting process over again. So far this has worked with over 500 MX67Cs at the company i work for. This worked for internal SIMs that had static IPs assigned and SIM that had no static IP assigned.   Thank you ... View more

Re: MX67C-NA Internal SIM Issues

by in Security & SD-WAN
‎Mar 23 2021 7:52 AM
1 Kudo
‎Mar 23 2021 7:52 AM
1 Kudo
After many discussions with Meraki and their engineers, the resolve to this issue was to activate the internal SIM card, after confirmation of the SIM being active set the internal modem to "enabled" - for some reason it setting to "enable" before the SIM is active, the MX doesn't like it, I have seen this on many many of our MXs. While the MX is plugged into power, remove the SIM tray, unplug the MX, re-install the SIM card while the MX is unplugged, Plug the MX back in.   That has solved most of the issues I have seen, and to be honest I completely forgot about this thread, and I never let yall know of the fix.    Few of the MX devices we had to replace the internal SIM cards with new ones as the MX would just not recognize there was an SIM installed. After preforming the above, we didn't need to add the APN, it finally pulled that info from the carrier, in this case it was Verizon. ... View more

Re: MX67C-NA Internal SIM Issues

by in Security & SD-WAN
‎Sep 28 2020 5:46 AM
‎Sep 28 2020 5:46 AM
If I am not mistaken the 15.x firmware is beta. That is something my company does not want on our prod equipment. We are only to use the SRC and RC at this time.   Thank you ... View more

Re: MX67C-NA Internal SIM Issues

by in Security & SD-WAN
‎Sep 24 2020 5:49 AM
‎Sep 24 2020 5:49 AM
yes in the US   ... View more

Re: MX67C-NA Internal SIM Issues

by in Security & SD-WAN
‎Sep 24 2020 5:48 AM
‎Sep 24 2020 5:48 AM
The APN to use with a SIM that has a static associated with it in the south area, is the so01.vzwstatic - that did not work with a static.    The APN to use with a SIM that does not have a static is the vzwinternet - that is not working either   Which is the main issue, I have tried all the ways i can think of to no avail.   The ISP main connection is constantly connected via port1 and the internal cell will show no signal  ... View more

Re: MX67C-NA Internal SIM Issues

by in Security & SD-WAN
‎Sep 23 2020 1:35 PM
‎Sep 23 2020 1:35 PM
Thank you for the quick reply, I should have mentioned the APNs i have tried.    vzwinternet vzwapp so01.vzwstatic - for the SIMs with a static IP and the Area codes they are activated in - according to Verizon     ... View more

MX67C-NA Internal SIM Issues

by in Security & SD-WAN
‎Sep 23 2020 1:24 PM
‎Sep 23 2020 1:24 PM
I am having a hard time getting any type of answer for the issues I am having with the internal SIM working on the MX67C-NA device.    I am using a SIM card from Verizon in the device. I have been told by Verizon and Meraki that Verizon has been certified to work with the MX67C-NA, but I am unable to get the sim to work in the device.    Actions taken:   Activated the SIM card with Verizon using the IEMI of the device ( with and without a static IP ) Update the APN in the Meraki portal (security & SD-Wan->Appliance status->Uplink->Cellular->APN) Contacted Meraki TAC to upload the APN on the back end - hard code Update the firmware to the 14.53 as suggested by TAC Removed the SIM put in phone and ensured it is getting a connection to the network - in a good service area - put back in the MX67C-NA - as suggested by Verizon   I have not had any luck with a connection, it will appear in the portal as connecting, enabled for a second or 2 then revert back to the Enabled state. I seem to be getting no where with any support on the Verizon side or the Meraki Side. We are in the US, if that makes a difference. Not sure what else to do.   We do have an external Cradle Point device connected to Port 2 as our failover, but we specifically got the MX67C-NA for the ability to use the internal cell connection, to not spend more on the external solution. We are not having any issue with the Cradle Point solution.   Any help or suggestions would be Awesome!!!   Thank you   ... View more
© 2024 Cisco Systems, Inc.