Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About Gareth_Parry
Gareth_Parry
Here to help
Member since Jun 29, 2020
Feb 21 2024
Community Record
12
Posts
5
Kudos
0
Solutions
Badges
Feb 21 2024
1:27 AM
yes it does. i already added the ip ranges of each of the sites to the route table with the hop via the VMX. i can ping the networks from a server in azure. its like its losing packets
... View more
Feb 21 2024
1:04 AM
Having said that i'm now having issues with my site to site connections, since i set up the anyconnect VPN. when on site i connect through the meraki site to site tunnels to a server in azure, i keep getting odd fails like "the connection has been reset" or when accessing sql "A transport-level error has occurred when receiving results from the server. (provider: Session Provider, error: 19 - Physical connection is not usable)'" when i connect the anyconnect VPN whilst onsite (so the traffic goes through this and not the site to site connection), it works fine.
... View more
Feb 20 2024
3:34 AM
2 Kudos
Got it! Both 10.0.0.0/24 and 10.0.2.0/24 were in the same VNET (under the subnet section) but i had not added 192.168.44.0/24 to the routing table. added and now working as expected. thanks for this
... View more
Feb 19 2024
4:24 AM
Hi, thanks but not sure what to do here. i have a route table for 10.0.0.0/24 do i also need to create a route table for 10.0.2.0/24? for the VM on 10.0.0.4 i have allowed inbound and outbound traffic from 192.168.44.0/24 and 10.0.2.0/24 thanks Gareth
... View more
Feb 19 2024
4:06 AM
Hi, could you expand more on this? I have a route table attached to the subnet for 10.0.0.0/24 that has all my sites in it with the next hope IP as 10.0.2.7 (the vmx) thanks Gareth
... View more
Feb 19 2024
3:53 AM
Hi, I have successfully installed a vmx in azure and created site to site VPN's from all our Meraki MX devices to the VMX. i can access resources in azure from our sites and vice versa. i have setup anyconnect on the VMX and can connect successfully however i cant reach any resources in azure or our sites. Azure resource range 10.0.0.0/24 with resource trying to connect 10.0.0.4 VMX resource range 10.0.2.0/24 with VMX on 10.0.2.7 anyconnect range 192.168.44.0/24 with client routing to send traffic going to destination 10.0.0.0/24 when i connect the anyconnect i can see the route 10.0.0.0/24 in the route details of the anyconnect client when i ping 10.0.0.4 from my client connecting via anyconnect i can see traffic in the vmx packet capture for interface internet but no response found. Has anybody had this before and have they solved it? thanks Gareth
... View more
Feb 12 2024
5:23 AM
Hi, I finally purchased some Anyconnect licenses. in the VMX netork i set up the anyconnect settings under client VPN. i set the client routing option to the destinations i want to send traffic through VPN on (one of which is the same range as the VMX and a server i want to be able to reach) i can connect the VPN. I see in the anyconnect client on my laptop that the routes i entered are shown, but i cant seem to reach anything. am i missing something? thanks gareth
... View more
Dec 20 2023
3:21 AM
HI, all i did was go into network connections from the windows control panel, then the properties of the VPN conenction to the VMX, then networking tab, properties on the IP4 entry, advanced button and unticked 'Use default gateway on remote network' im guessing there is more to it than this? thanks Gareth
... View more
Dec 19 2023
9:10 AM
HI, I have set up the VMX in Azure and all has gone quite well. I can reach each of our depots from the VMX. I have then set up a Client VPN using windows VPN client on my laptop. i set it to connect to the VMX network, and set it to split tunneling. this connects fine. i then want to access another device on another Meraki network from my laptop. i was expecting the traffic to go from my laptop, to the VMX, to the other network and then to the device. this doesnt seem to work. have i done something wrong here? thanks Gareth
... View more
Dec 12 2023
8:49 AM
2 Kudos
hi The VMX-s solution sounds interesting. Can you confirm my understanding: It will install a virtual MX device onto the Azure network, which will appear in my meraki dashboard. I then set up VPN from my physical MX devices (networks) to the virtual one. once complete then all networks will be able to access all resources at the other networks and Azure (i have a VM with SQL server on it that i want all sites to access)? can i then use a client VPN on a Laptop to connect to the VMX in azure and then have access to a resource at one of the other sites. i.e. i can connect to the VMX in azure and then connect to the CCTV Appliance, VIA IP address, at one of the other networks? thanks Gareth
... View more
Dec 11 2023
7:18 AM
Hi, I have a MX65 sat behind a BT Router and wanted to create a static Tunnel to a gateway in Azure. I had an issue with double NAT'ing, so ended up setting the BT router to bridge mode. This all worked fine. i have now moved to BT with Hybrid connect, but have just been informed that the hybrid connect does not work with Bridge mode. (and bridge mode is not supported on the smart hub 3) are there any other option to make this work, but keep the hybrid connect as a backup? thanks Gareth
... View more
Labels:
- Labels:
-
Firewall
Jun 29 2020
4:45 AM
1 Kudo
HI, Could you help more on this. If all inbound traffic is blocked by default and we have no forwarding set up, how is internet traffic and FTP traffic coming through? thanks Gareth
... View more
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 2 | 2695 | |
| 2 | 2880 | |
| 1 | 26467 |
© 2024 Cisco Systems, Inc.
