The Meraki Community
Register or Sign in
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 
  • About Pablo_
Pablo_

Pablo_

Conversationalist

Member since May 28, 2020

‎05-29-2020
Kudos from
User Count
PhilipDAth
Kind of a big deal PhilipDAth
1
Nash
Nash
1
View All
Kudos given to
User Count
cmr
Kind of a big deal cmr
1
Nash
Nash
1
View All

Community Record

4
Posts
2
Kudos
0
Solutions

Badges

Lift-Off View All
Latest Contributions by Pablo_
  • Topics Pablo_ has Participated In
  • Latest Contributions by Pablo_

Re: MX84 with two internet links. One in failed state, but transmitting

by Pablo_ in Security / SD-WAN
‎05-29-2020 04:49 AM
2 Kudos
‎05-29-2020 04:49 AM
2 Kudos
You nailed it. I trusted the ISP DNS servers instead of going with Cloudflare.   Once I set 1.1.1.1, the DNS test succeeded and the link became active. The link you added was very useful in understanding the process.   Thank you!   Pablo ... View more

Re: MX84 with two internet links. One in failed state, but transmitting

by Pablo_ in Security / SD-WAN
‎05-28-2020 12:34 PM
‎05-28-2020 12:34 PM
Thank you, guys. I'll let it run for a bit with the new target IP. So far it's testing fine on both, but remains in failed state. Will try to force traffic through the one marked as failed with an SD-WAN policy too.   Best,   Pablo ... View more

Re: MX84 with two internet links. One in failed state, but transmitting

by Pablo_ in Security / SD-WAN
‎05-28-2020 12:00 PM
‎05-28-2020 12:00 PM
Hello, and thank you for your message.   The traceroute shows the MX can reach 8.8.8.8 with either link, and in each case going through the ISP assigned to that link.   I've added 172.217.10.142 (one of google.com's addresses), and i get the same results: I can run a traceroute from the MX, each one goes a different route and through the ISP connected to each link, but WAN1 remains in failed state.   The historical data seems to show that 8.8.8.8 is reachable for both connections too:     Thank you, Pablo   ... View more

MX84 with two internet links. One in failed state, but transmitting

by Pablo_ in Security / SD-WAN
‎05-28-2020 09:26 AM
‎05-28-2020 09:26 AM
Hello,  I have an MX84, two internet links (100Mbps each). WAN2 shows as Active, WAN1 as failed.  Both are configured with static IP addresses, and worked when tested with the same addresses from a laptop connected directly to the ISP.   What is strange, is that a traceroute from the MX will show the correct path when tested with each uplink. WAN1 (in failed state), will show the expected next hop and the ISPs internal hosts. Those will be different from WAN2.   Hourly tested is configured in SD-WAN, and both links show packet loss near 0% (WAN1 shows 100% until it was plugged in, of course)     The route table shows:   The configuration is below. Clearly, traffic can flow on that interface, but status will not change to Active, and I suspect this means it will not send client traffic through it (it is configured to load balance).   I've restarted already. Any ideas?   Thank you, Pablo     ... View more
Kudos from
User Count
PhilipDAth
Kind of a big deal PhilipDAth
1
Nash
Nash
1
View All
Kudos given to
User Count
cmr
Kind of a big deal cmr
1
Nash
Nash
1
View All
My Top Kudoed Posts
Subject Kudos Views

Re: MX84 with two internet links. One in failed state, but transmitting

Security / SD-WAN
2 5731
View All
Powered by Khoros
custom.footer.
  • Community Guidelines
  • Cisco Privacy
  • Khoros Privacy
  • Cookies
  • Terms of Use
© 2023 Meraki