Haven't played with this on the Meraki Go hardware, so I may be way off-base. They may have similar terminology and setup for Meraki Go. Hope this helps.   However on Meraki enterprise you have the option of Hub / Spoke VPN. 1 site is the hub, the other are spokes and send the data to the hub. Within this the is a setting for "default route". This would funnel all traffic from the "spoke" to the "hub" then out. This sounds like what you are asking for. The other option within this is a "split tunnel" (unchecking default route). This would only send data destined for the hub down the VPN tunnel, all other traffic is sent out the wan interface (not down the tunnel) ... View more

Glad to here it. I would still remove the "Wifi Router", or try to re-deploy  in AP mesh-mode only. ... View more

@AvroNot sure this would benefit Meraki Go. It is designed for large enterprise deployment and Go is more of a simple solution. I generally do not enable unless we have a large & dense deployment with something like Radius running for authentication. If you require this, you can always deploy Meraki Enterprise.   https://documentation.meraki.com/MR/Wi-Fi_Basics_and_Best_Practices/802.11k_and_802.11r_Overview    https://documentation.meraki.com/MR/Wi-Fi_Basics_and_Best_Practices/Roaming_Technologies  ... View more

Happy these are here. Sad @MiriamK and @JamesMW didn't give me heads up first! I would like to test out a full stack with the GX50, GS110p and these AP's. I have been waiting on a deployment. Let me know what you can do for us. -Pedro ... View more

I don't think that is an option. Meraki Enterprise also does not allow this. You need to create rules to allow the traffic you want to permit. You can get pretty in-depth with rules on Meraki Ent gear, however I have not done much with "Go" when it comes to firewall rules. If this is not an option for, you will need a plain ol' router, not a firewall with NAT/PAT. ... View more

Plug a cable into the GX and test you speed from there 1st. That will give you a baseline for wired speed.   You are currently triple NAT with 3 routers. That is not good 😞 You really should be using the Xfinity for modem only, then firewall, then switch / AP. Additionally if you AP's are not cabled/hardwired to your router/switch you could be forcing them to "half" the speed because they are send & receive over wifi. With networking, often, "less is more". Meraki also works best in "full stack" (firewall/switch/AP), it also you to administrate them all from a single interface.   PS: All wifi will interfere with one another. It's radio and susceptible to noise from other radios. Learn about SNR. We often fix large wifi deployment by turning the power down on AP's to reduce interference. ... View more

Site to site VPN on Meraki Enterprise gear is excellent. Save yourself and your customers and just get them. They do cost, but will end up saving money in the long run. We have MX-to-Z3 networks and MX-to-MX networks (+8 VPN mesh) all running for years w/o issue or additional config. ... View more

Hi @MiriamK What if we are both consultant and provider? Should we pick one, or is benefit for Meraki either way. ... View more

This forum is for Meraki Go, not Meraki Enterprise. You can re-post you question there, or use the answers below. Best practice would be to deny the feature within application rather than to firewall it at the perimeter.   https://support.google.com/chrome/a/answer/2799701?hl=en    https://support.google.com/chrome/thread/97729787/how-do-you-disable-not-remove-chrome-remote-desktop?hl=en    ... View more

Here we go again. I think I just got the last user fixed up from last time. It was just Patch Tuesday. Anybody have a corporate MS account and can open a ticket there also? ... View more

Looks like Microsoft's fix is still "do it yourself". Still getting user issues. Tried to have a user self-repair last night, no luck, no update available. I at least hope MS pulled down this update. ... View more

Etsa misma:   pausar la actualización wusa /uninstall /kb:5009543 reiniciar   Buena suerte! ... View more

Thanks for the update. We also realize how hard it is to get equipment in customer hands lately. Please let us know! ... View more

Thanks again for the help. If anyone has a permanent solution or what exactly the update changes, please let us know. This has been happening all over for us. ... View more

Update downloaded and installed itself again on one machine today (after removal yesterday). ... View more

Try a reboot for the 809 error. I tested to see if the rollback worked without restart (even after prompted) on a machine and got the 809 event. ... View more

Bumping this back up. Wi-Fi 6 (6e or wave 2) is basically required for any new hardware purchases. ... View more

This is a mess. MS keeps screwing up. Starting to feel like the old days with Windows Updates. Thanks for the help. Removing  KB5009543 working on a few machines already. ... View more

Meraki is worth billions of dollars and you are offering us socks? Up yours Meraki, I can buy my own socks. ... View more

@DHAnderson I had been signed up for beta for quite a while. John w/ Meraki reached out to me via email and I tested it the same day. So far so good. I don't use it much, but do not care for Mobile Apps. Happy that Meraki Go is trying. Looking forward to some new features and new hardware from them 😉 ... View more

Working well. Big bonus for us MSP's. ... View more