Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Register or Sign in
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About KarstenA
KarstenA
Here to help
Member since Feb 27, 2019
Sep 23 2020
Community Record
10
Posts
0
Kudos
1
Solution
Badges
Sep 11 2020
9:05 AM
S390 switches can support a total count of 1000 VLANs per stand-alone switch or switch stack. VLAN ID 1-1000 are configured by default. It supports VLAN IDs > 1000 but only support 1000 VLANS, VLAN ID 1-1000 are configured by default, and when mangement vlan is >1000 there are 1001 VLANS. We got it confirmed på Meraki Support and its a known problem. We found a workaround. Set managment vlan on the switch to 1 and Switch > Configurere > Switch Settings > Management VLAN 1 before you move it. Thanks for yourtime
... View more
Sep 8 2020
3:11 PM
I only have MS390 available for this network and I cannot add either the switches I have removed or new switches. I have the feeling that there is still a switch configuration, even though all switches have been removed. And the default switchport configuration is trunkt native vlan ie. 1000 vlans but management VLAN on the switches in I removed is 15xx, so it must be 1000 + 1.
... View more
Sep 8 2020
9:52 AM
Yes VLAN 15xx and then i removed the switch from the network and now i can not add it back in to the network. There are no other switch in that network.
... View more
Sep 8 2020
6:53 AM
Hi I'm able to claimed the switch(MS390-48UX2) but when i tries to add the switch to network i get following message ***This switch is limited to 1000 vlans, Please check your vlan related configurations on all ports, and static and management vlans on the switch and network. Note vlan 1 is always open*** We do not have 1000 vlans in that network. We have 5 vlans to the connected AP's which is connected to Cisco Classic 2960s
... View more
Dec 9 2019
11:41 PM
Thanks for your answer. Yes i did thought of that but I was hoping not to change anything at the ISP as i want to manage the routing. But i think its going to be the solution. Thanks again.
... View more
Dec 9 2019
11:10 AM
Good Evening My challenge is that I have 2 L3 MPLS, one must be the default route for data and voice vlan + meraki management vlan and the other must be the default route for guest wireless vlan. I know that MS410 does not support PBR or VRF. Any tips how i can accomplish that, whitout truking it to an another L3 device / L3 switch with a seperate routing instanse
... View more
Sep 2 2019
4:55 AM
But that did not answer my question, is it possible for Meraki Support Engineer to change MTU by Port and VLAN basis
... View more
Aug 12 2019
12:01 AM
The problem is that the packets get fragmented at the firewall (ASA 5512-X) we got some issue with Microsoft Teams / Voice when fragmented
... View more
Aug 9 2019
9:30 AM
Is it possible to run Jumbo frames 9K only on switchport or VLAN basis. Need this for a closed SAN network. There are user vlans on that switch as well, change the default MTU size on the switch is no plausible
... View more
Aug 8 2019
5:06 AM
Is there any way to see which SFP type is insterted in a MX, as you can see SFP type on a MS
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 3284 | Sep 11 2020 9:05 AM |
© 2024 Cisco Systems, Inc.
