Community Record
17
Posts
6
Kudos
0
Solutions
Badges
4 weeks ago
I will explain the scenario. 3 switches are stacked as below. POE 1 NPOE 1 NPOE 2 POE 1 is connected with wifi AP & IP Camera since it is POE powdered. But the PC mac (which starts with A8:B1) is connected in NPOE 1 switch & 9C:E3 starting mac shown is of the NPOE2 meraki switch mac. The 1st uplink for the stacked switch is given to NPOE2 & 2nd uplink is connected to POE 1 but 2nd uplink is blocked here due to STP.Only 2 fiber uplinks are connected to this stacked switch.
... View more
4 weeks ago
The above is an event log message from Meraki MS210-48 model switch, here port 26 & 33 mentioned here is data vlan 404 which are desktop pcs. They are having device mac id which starts with A8:B1 . why it is showing here "mac address flapping" & the mac ids mentioned here "9c:e3" etc which starts with are of the meraki switch which is connected to the current switch (both the switches are stacked).Can anyone explain in detail about the output & why it is showing other stack member switch mac id here?
... View more
a month ago
Can u pls explain Is the poe device asking for 30 w or 10.2 w from the switch?
... View more
a month ago
What is the meaning of budgeted 1008 W/740 W. Here what does it mean by the values?Total power of the switch is 740w then what is 1008 w?
... View more
a month ago
When I was checking the meraki poe switch (model - MS225-48FP) this shows there. What is the meaning of each consumption, budgeted and their corresponding values?
... View more
what is the solution for this? How come meraki can avoid this feature, as it was available on catalyst for cli.
... View more
How do i see the temperature running on meraki models MS225 & MS210 in meraki dashboard? earlier when i was using catalyst cisco switches i could see the env temperature and fan status of those switches in the command line.
... View more
other stack members were online and I was able to ping also. No issues.The end devices which was connected I didnt check that.
... View more
Actually i was able to open the dashboard and when I checked 1 switch was showing offline for 1 hour at the time, (all the switches were online), when it showed offline i pinged to that switch then it says ping out.And after 1 hour it came online and it started pinging. There is no issue with the dashboard because I was able to see other online switches at that time.Only for this particular switch is the issue
... View more
I have checked at the time that issue happened, there was no ping to the switch ip address.
... View more
Yes. Helipad is there but it is bit far away.
... View more
This switch is just an access switch (1 among many meraki access switches) which is connected to a distribution switches (meraki). Out of all meraki access switches only this particular switch faced "no connectivity" issue which has happened 2 times yesterday and day before yesterday. This particular switch is connected as a stack between 3 switches in a rack. But the other 2 stack members didnt face any issue at that time. (All are meraki models)
... View more
Its a hospital infra. We use Meraki APs in our building. So is there any conflict happening between Meraki wifi APs which are nearby?
... View more
The above message is showing for an wifi ap. Can anyone explain what is this issue, its cause & how to resolve?
... View more
Last 2 days no connectivity was showing for few mins it got rectified after 30 mins automatically, when I checked the event log it says "Device boot reason: power event or other". But device uptime is saying more than 20 days. This issue happened yesterday and day before yesterday. What is the reason for this If the switch got rebooted or power disruption was there then the device uptime should get updated accordingly.
... View more
My Top Kudoed Posts
