Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About RayR
RayR
Here to help
Member since Apr 22, 2024
Aug 15 2024
Community Record
17
Posts
2
Kudos
0
Solutions
Badges
Aug 15 2024
9:18 AM
2 Kudos
I don't have a PoE capable switch - that's why I purchased the PoE injector. This is a home network. The direct connection is to an MX67 - on a straight run of shielded Cat6 (via the PoE injector - of course). That said - the condition has now cleared (perhaps I didn't give it enough time after replacing the previous 802.3af PoE supply). Thanks
... View more
Aug 15 2024
6:57 AM
My MR 36H is alerting "running in low power mode" I have a Meraki 802.3at POE injector and only 50' of good quality Cat6 cable. Can you help me diagnose what's wrong? TIA
... View more
May 12 2024
1:34 PM
Previously associated clients stop passing traffic. And the AP "disappears" / stops advertising the ssids.
... View more
May 10 2024
2:24 PM
As requested. I had wanted to make the Native VLAN for port 2 (the port the MR is connected to) = VLAN 1 - but when I do that - things cease working.
... View more
May 10 2024
1:21 PM
I'm not sure that I understand your answer. I want the to set the Native VLAN on the port to be VLAN 1 - so untagged traffic will use VLAN 1 (e.g., wired interfaces that connect through that port). But it does not work - so I'm trying to understand why... Thanks
... View more
May 10 2024
9:07 AM
I have a VERY simple network: Internet - MX67 - MR36H A few vlans on the MX and SSID's on the MR mapped to them (vlan tagging) Ports on the MR36H mapped to a specific SSID (port profiles) When I assign the MX port that the MR connects to to Native VLAN 1 (per port vlan settings) - things do not work. Trying to understand why? (I'd assume this is what I want - so untagged traffic coming in from any wired devices connected through the MR36H are put on VLAN 1?) Sorry if this is an obvious question - but I'm missing something here. Thanks
... View more
Apr 30 2024
8:11 AM
Changed mx lan port to. "Drop untagged traffic" and now that works fine - THANKS A follow up if you don't mind? I assume if I map a port on the mr36 to an SSID, traffic that comes in on that port will be tagged in the VLAN associated to the SSID- correct?
... View more
Apr 30 2024
7:48 AM
Thanks. I'll give that a try when I get back to my desk later today. Since I want to run multiple ssids each in a separate VLAN, I assume the first of your two suggestions is the way to go? By the way, just out of curiosity, I'm wondering why the default for the lan port couldn't be the same? Any going to try later today. Thanks
... View more
Apr 30 2024
6:15 AM
I corrected SSID FW issue and MX port issue and returned to “external DHCP” on wireless config (as I want MR clients to get DHCP leases from the MX - which I believe appropriate for running multiple vlans?). Now I get an address / connection to MR – but no internet connection. Advice?
... View more
Apr 29 2024
8:57 PM
Physical config: Client - to MR36 - to MX67 - to Comcast Logical config: SSID on MR maps to VLAN 1. Address assignment on MR set to "external" - as I want to use DHCP on MX - not MR. Fails... If I change to Meraki "AP assigned" - things work - but that's not what I had wanted - as I want to use multiple vlans in the network - which I belive means I need to use DHCP from MX - not from MRs - correct?
... View more
Apr 29 2024
7:22 PM
Trying to turn up a new network - and getting this error message: xtra: no_offers_received, vap: 0, vlan: 1. Can't figure out why. Appreciate guidance.
... View more
Apr 22 2024
7:36 PM
Never mind - Found my answer: MR36H will use a 4-Port profile (same as MR30H), however, port 4 of the profile will not be used since the port does not exist on the AP. For more information about MR36H ports please visit installation guide.
... View more
Apr 22 2024
7:00 PM
I'm trying to set up port profiles on an MR36H - but I'm confused. The dashboard config settings list Ports 1 through 4 - BUT the device has an "unmanaged" port and three other ports (numbered 1 through 3). So - I am confused. Can I actually put a port profile on the unmanaged port? And, if so, is it considered port 1 or port 4? TIA
... View more
© 2025 Cisco Systems, Inc.
