Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About HaniAbuelkhair4
HaniAbuelkhair4
Getting noticed
Member since Aug 23, 2021
May 1 2023
Community Record
62
Posts
15
Kudos
2
Solutions
Badges
Oct 19 2022
8:48 AM
I have two printers and each printer is connected to deferent swatch Meraki MS120-48LP And these printers are losing the connections from time to time Both were working fine but now are not stable and the log i have the following I checked the cables from the meraki dashboard and its all OK I have other printers and all of them are ok but these two Any suggestion ? Port status change port: 41, old: down, new: 100fdx Port STP change Port 41 designated→disabled Port status change port: 41, old: 100fdx, new: down Port STP change Port 41 disabled→designated Port status change port: 41, old: down, new: 100fdx Port STP change Port 41 designated→disabled Port status change port: 41, old: 100fdx, new: down Port STP change Port 41 disabled→designated Port status change port: 41, old: down, new: 100fdx Port STP change Port 41 designated→disabled Port status change port: 41, old: 100fdx, new: down
... View more
Labels:
- Labels:
-
Interfaces
Oct 12 2022
7:12 AM
1 Kudo
I can confirm now all problems solved after the downgrade @Meraki I think think Meraki support need to take an action as it will force the upgrade again and fix that bug on 17.10
... View more
Oct 11 2022
10:31 AM
1 Kudo
In my case was MX with Built in WiFi
... View more
Oct 11 2022
9:38 AM
I have the same issue and will try to Rollback now and see
... View more
Oct 7 2022
11:59 AM
Yes its disabled already for the VLAN But the main issue is my WAN is getting V4 and V6 IP address at the same time using WAN1 only
... View more
Oct 7 2022
11:29 AM
Local VLAN's are disabled already its enabled on the WAN and getting both v4, and v6 but there is no option t disable V6
... View more
Oct 7 2022
11:28 AM
Its not an option And on the Address and VLAN's you can see the WAN interface at all
... View more
Oct 7 2022
8:13 AM
I found this on my MX merkai and not sure if its OK I have only WAN1 with both IP's V4, and V6 Is this OK and tried to disable IPv6 on my WAN could not find way to do that Any advise I have complains of slow internet
... View more
Labels:
- Labels:
-
Firewall
Oct 5 2022
12:41 PM
I have MX67W And created 2 SSID's one for the staff and one for Guest Can i limit the bandwidth for the Guest SSID? If have MR AP's then its easy and the config is on the SSID setup. But as i am using the bult-in MX67W i cant find that option on the SSID setting! Tried to check the SD-WAN and QoS section by creating new policy and add my local Guest IP range and set the bandwidth but i was not sure if its the right way to do it as the limit bandwidth was max 5Mbps but i need to give them more like 50Mbps. Any suggestions ?
... View more
Labels:
- Labels:
-
Other
Sep 8 2022
10:24 AM
@Brash Thanks Just want to confirm that
... View more
Sep 8 2022
9:24 AM
Hi, Trying to use Windows server as VPN server using L2TP protocol behind MX I know that L2TP VPN will need DP 1701 — UDP 500 UDP 4500 NAT-T Protocol 50 ESP As the Windows server behind the MX NAT devise and the windows server dose not have public IP I was readding about this and its fact that port forward will not help for the ESP protocol and i should use NAT-T instead So i think i need to change the registry on the Windows server to allow NAT-T, and then end user machine registry to allow NAT-T but do i need to do any thing from the MX to allow NAT-T maybe one to one NAT but this will need an extra public IP Any ideas if someone have same setup ? Thanks
... View more
Sep 7 2022
5:48 AM
1 Kudo
same here this this is not the 1st time to consider Office update as Malicious Anyone contacted Cisco Support ?
... View more
Jun 9 2022
7:14 AM
Still i am getting error
... View more
Jun 7 2022
5:51 AM
Thanks @PhilipDAth
... View more
Jun 6 2022
9:29 AM
I found the issue its the Wins server But i could not find away to setup the wins server on my DHCP setting if you have DNS server you can set that on on the Custom nameservers on the DHCP, but i dont know where can i force my wins server on the DHCP Only Client VPN you can see the Custom nameserver for wins not the DHCP I remember that the we have the DHCP option but dont know the ode for Wins any help please
... View more
Jun 6 2022
7:54 AM
I have two offices that I'm going to connect with a site-to-site VPN. I have two Meraki MX64's and have setup the site-to-site using Hub (Mesh) mode. I performed a test of the VPN it seemed to work well. I could ping between sites, and i can ping the windows server that is my DNS and shared folder server, I am unable to ping the domain name or server name. I have 4 sites on that site to site VPN group accessing the same shared folder with no issues, only this remote site i have the site to site VPN up and i can ping both sites with no issues and i can map the shared folder by IP but i need the domain controller to be reachable by name not IP. I have configured the DNS server on the DHCP to point to that DNS server Custom nameservers similar to other location but again hostname is not resolving. Any suggestions or ideas ? Thanks
... View more
Labels:
- Labels:
-
Auto VPN
Jun 1 2022
11:14 AM
If no certificate is present, it will be necessary to install a Self-Signed certificate. If a certificate already exists, please ensure that it has been configured with the necessary parameters for TLS is this must on the AD server .
... View more
Jun 1 2022
6:42 AM
Thanks for the update Any special configuration need to be done of the AD side ?
... View more
May 31 2022
11:59 AM
Appreciated your support on this case Today i have windows server been used as VPN server, and now since we have the Meraki i need to shift the VPN from the windows server to the Meraki and i still need to use the active directory for user authentication. I found this document but my question is I have the following documentation and my question is https://documentation.meraki.com/MX/Content_Filtering_and_Threat_Protection/Configuring_Active_Directory_with_MX_Security_Appliances Do i need to to add the active directory on Log into Dashboard and navigate to Security & SD-WAN > Configure > Active Directory first then configure the VPN authentications or i have to do the client VPN authentication directly? And can i do that in parallel to the to the existing service on the VPN windows server for easy migration ?
... View more
Labels:
- Labels:
-
Client VPN
Feb 23 2022
5:02 AM
Thanks By any chance do you know any software that i can use to test the speed between the main office and end user home like install software at the head office and try to measure the speed from the end user home to confirm the issue ?
... View more
Feb 22 2022
9:06 AM
Do you open port 80 for the Unifi Devices (AP's and 8 Port Switches) ?
... View more
- « Previous
-
- 1
- 2
- Next »
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 7876 | Oct 7 2022 11:54 AM | |
| 1117 | Feb 22 2022 8:45 AM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 6 | 1117 | |
| 1 | 14588 | |
| 1 | 14592 | |
| 1 | 14858 | |
| 1 | 15473 |
© 2024 Cisco Systems, Inc.
