New articles:
Using Umbrella Multi-org with Cisco Secure Connect
Change: New article.
Secure Connect:
Cisco Secure Connect Account Setup FAQ
Change: Added note that Umbrella customers with the Multi-org can continue to use Multi-org with Cisco Secure Connect. To do this, they must order Multi-org at the same time when they order Secure Connect. It's crucial to note that there is no direct integration between Secure Connect and Multi-org. Customers can access Multi-org via their existing Multi-org dashboard. Furthermore, the use of Multi-org will remain limited to DNS content and security policy management.
Cloud Monitoring for Catalyst:
Cloud Monitoring for Catalyst Onboarding
Change: Added note that when onboarding a stack, the single management IP should be entered which will onboard the entire stack.
MX/Z:
MX Cold Swap - Replacing an Existing MX with a Different MX
Change: Added section "Re-generate AnyConnect custom certificate (optional)".
Change: Added note that the mentioned behavior is specific to traffic initiated by the MX appliance itself, any Meraki devices connected downstream will always adhere to the route priority of the MX, added ports for management traffic and AMP registration and file disposition lookups.
Configuring Active Directory with MX Security Appliances
Change: Added note that communication with the server will originate from the highest numbered VLAN included in the VPN, if the Server IP address is located over a VPN Tunnel.
AnyConnect on the MX Appliance
Change: Updated note that custom hostname certificates require MX firmware version 16.16+.
AnyConnect Authentication Methods
Change: Added note that TLS is required to communicate with the Domain Controller for Active Directory authentication.
Change: Added note that MX utilizes LCP (Link Control Protocol) to assign IPs to clients, thus DHCP and Static Assignment are not supported.
MX75 Hardware Installation Guide
Change: Added MA-PWR-100WAC-A to Accessories.
MX250/450 Series Hardware Installation Guide
MX95/MX105 Series Hardware Installation Guide
MX85 Series Hardware Installation Guide
Z3 and Z3C Overview and Specifications
Change: Updated throughputs.
Change: Added Verizon (US) to certified carriers.
Meraki MX/Z Security and SD-WAN Licensing
Change: Added Z4 license SKUs.
Change: Added Z4C TAC Range.
MS:
Change: Added "Topology changes" to packet counter table.
MS Switch Access Policies (802.1X)
Change: Updated RADIUS Testing. If unreachable, the switch would transition into an alerting status to indicate a failure. Actual server failover is based on the client authentication requests. Failed client authentications will have the switch failover to the next available configured server.
FAQs: Migrate to Meraki management mode
Change: Updated FAQ "If I already have DNAC essential/advantage licenses, do I need to purchase another license to use the Meraki dashboard today?", "Can I access the console after I initiate the migration?" and "What do I need to do if I want to migrate back to DNA management mode?".
Change: Added warning about MS390s existing in the same co-term Organization will require the same license edition (either Enterprise or Advanced) as the Catalyst 9300-M. License types cannot be mixed and will result in an incompatible license error (and vice versa).
MR:
HTTP CONNECT Proxy Support on MR Access Points
Change: Added notes for correct formatting for using the "Option 43" method.
Change: Added CW9163E.
Scanning API for Location Analytics Solutions
Change: Added differences 4, 5 and 6 to FAQ "What are the fundamental differences between V2 and V3 versions of the Scanning API?".
Change: Updated regarding Wi-Fi 6E / 6 GHz wireless.
Change: Added note that a Lease Time of 24 hours will be given to wireless clients.
Meraki Local Authentication - MR 802.1X
Change: Added note to consult vendor-specific documentation to determine the exact path to a device's certificate store or IdenTrust Commercial Root CA 1.
High Density Wi-Fi Deployments
Change: Added note that once an antenna is detected by the AP it cannot be changed in dashboard until the antenna is removed and AP is rebooted.
MT:
Change: Added section "2 Free MT Licenses with MR Advance License".
General Administration:
Behavior during Connection Loss to Cisco Meraki Cloud
Change: Added reboot behavior for different MX firmware versions.
Managing Multiple Networks with Configuration Templates
Change: Added note that Firewall rules on Template networks do not show a hit counter column, which is expected behavior for this column to be missing.
Changing the Dashboard Network Time Zone
Change: Added note that Winter and Summer time (Daylights savings time) is automatically applied by the dashboard.
How to do a License Transfer in Cotermination
Change: Added note that transferring between a Co-Termination Licensing Organization, to a Per-Device Licensing Organization or vice-versa is not possible.
Organization Split Overview and FAQ
Change: Added "Secure Connect Organizations" to section "Limitations of Organization Splits".
Managing Dashboard Administrators and Permissions
Change: Added note that Read-Only admins can perform switch port cycles and cable tests.
SM:
Change: Added section "Version 4.x+ with Bulk Enrollment Token"; updated section "Version 3.5.x - 3.9.x".
Misc:
Change: Added references to free online training courses on the Meraki Learning Hub.
Is there a typo in : https://documentation.meraki.com/MX/MX_Overviews_and_Specifications/MX67_and_MX68_Datasheet
Top section mentions that the MX67 and MX68 have 700/400Mbps of throughput but the bottom section says 600/300Mbps :
