Secure Connect:
Cisco Secure Connect Reserved IP
Change: Added additional guideline #5.
Cisco Secure Connect - Cloud Firewall Policy
Change: Added "IPS service does not inspect traffic matched by the private rules."
MG:
Change: Added MG52 and MG52E.
MX:
Change: Added "Allow list URLs entries support trailing wildcards (e.g., http://meraki.cisco.com/*)."
Meraki and ThousandEyes Integration Troubleshooting
Change: Updated workaround for issue "The MX sends test traffic sourced from the 6.0.0.0/0 IP Address range": "Change the MX mode to NAT and add a VPN-enabled VLAN."
Change: Added FAQ "Which models MX/Z support this integration?"
IPv6 Support on MX Security & SD-WAN Platforms - Core Fundamentals
Change: Added Z4 and Z4C.
Change: Added "MTU adjustments do not affect Non-Meraki VPN and Client VPN tunnels."
Change: Added "MX-Z appliances in Passthrough or VPN Concentrator mode cannot be used to initiate interesting traffic into the tunnel. Interesting traffic would need to be initiated from a client behind the Passthrough appliance."
MS:
Connect Hybrid Operating Mode Catalyst Switch to Dashboard
Hybrid Operating Mode for Catalyst Cloud-Managed Switches - Overview
Change: Added "If you do not yet see a notification in Dashboard announcing the availability of hybrid and cloud operating modes, your organization is not yet enabled. Any devices added to your organization via Dashboard will be fully cloud-managed (cloud operating mode)."
Connect Hybrid Operating Mode Catalyst Switch to Dashboard
Change: Added "Organizations using per-device licensing must use the network-wide add devices page."; added "Only the new version of the Inventory page is supported. If you see the option to Try New Version, you must select this to continue."
Change: Added note "The Allow listed snoop entries is expected to be empty on normal operation. The IP-to-MAC bindings learned via the DHCP Snooping table will not appear. Once a client has been manually moved or added it will populate."
MS NetFlow and Encrypted Traffic Analytics
Change: Added "SNMP polling is enabled by default in the latest Cisco's Secure Network Analytics (SNA) version. SNMP polling on SVIs is not supported on Catalyst based (MS390/9300) switches running CS-based firmware."
Change: Updated specific devices models.
Change: Added "We strongly recommend you power down the entire switch stack before adding a new member to avoid packet forwarding issues. Power on all members simultaneously once the stack is rebuilt"
MR:
Low Power Mode on Cisco Switches
Change: Added "For Low Power Mode situations seen on APs connected to Cisco Catalyst switches, ensure LLDP is enabled on the switch. For instructions, you can consult the section How to enable LLDP in a Cisco Catalyst Switch."
Meraki Health - MR Access Point Details
Change: Added "Both Onboarding and Performance metrics are calculated based on the past 2 hours, regardless of the timeframe selected in the dropdown menu."
Change: Updated based on the new version of the page.
Change: Added Wi-Fi 7 access points.
Cloud-Managed Hybrid Operating Mode for Catalyst Wireless LAN Controllers
Cloud-Managed Hybrid Operating Mode for Wireless Controllers LAN Controllers Requirements
Cloud-Managed Hybrid Operating Mode for Catalyst Wireless LAN Controllers FAQ
Cloud-Managed Hybrid Operating Mode for Catalyst Wireless LAN Controllers Design Guide
Quick Start Guide: Cloud-Managed Hybrid Operating Mode for Catalyst Wireless LAN Controllers
Change: Renamed from "Cloud Monitoring for Catalyst Wireless".
Cloud-Managed Hybrid Operating Mode for Wireless Controllers LAN Controllers Requirements
Change: Added minimum required software releases.
MV:
Meraki Vision Portal Changelog
Change: Added release notes for up to v1.24.4.
Change: Added "MV84X cameras do not support standard retention and default to Smart Retention."; added MV53X.
Camera and sensor-only admin (IoT Admin)
Change: Added "Camera and Sensor role name(s) created do not need to be created under Organization > Configure > Administrators > SAML administrator roles."
General Administration:
Ways to Contact Meraki Support
Change: Added section "Legacy Version of Case Submission in Support Center".
Support Center Case Submission
Understanding Case Severity Levels
Change: Updated information about the availability of the new case submission experience.
Meraki Dashboard Organizational Structure
Creating and Deleting Dashboard Networks
Change: Added "Network Scope General Recommendation: One network per physical location or branch".
Change: Added "IOS XE 17.15" for Intelligent Capture; added "Intelligent Captures are enabled by default for networks that are matching the requirements."
SNMP Overview and Configuration
Change: Added section "SNMP Timeouts"; added "There are two distinct places to configure this in your Meraki dashboard. These settings operate independently from each other and can be enabled and disabled separately if desired." incl. the locations to configure them.
Returns (RMAs), Warranties and End-of-Life Information
Change: Added "Please note some Cisco Meraki devices do not need to be returned and can be e-wasted. When looking at the RMA in PRR, if there is no 'Return' tab, the device does not need to be returned. Cisco Meraki Support can confirm this for you if you cannot view the RMA in PRR. You can engage the Cisco "Takeback and Reuse" program. Please note you will need to log in with your CCO ID."; added "After you submit the RMA, you will receive an RMA number and be directed to Cisco’s Product Online Web Returns (POWR) tool to schedule carrier pick up or print a pre-paid return label to return the trial."
Change: Added "IPv6 Support", "Layer 7 (Application) Enforcement powered by NBAR", "Traffic Shaping Enforcement powered by NBAR", "Catalyst + Meraki SD-WAN Interconnect (eBGP over IPsec)", "IPsec SSE tunnel monitoring, redundancy, and DIA", "Cisco XDR Integration", "SD-AVC Integration - Smart Application Updates Delivered via the Cloud", "DH15 and DH21 support in IPsec" and "Trusted Traffic Exclusions powered by NBAR".
Meraki MX/Z Security and SD-WAN Licensing
Change: Added "Catalyst + Meraki SD-WAN Interconnect (eBGP over IPsec)", "IPsec SSE tunnel monitoring, redundancy, and DIA", "Cisco XDR Integration", "SD-AVC Integration - Smart Application Updates Delivered via the Cloud" and "DH15 and DH21 support in IPsec".
Information for Cisco Meraki for Government users
Change: Added sections "Support Coverage & Hours" and "Severity Levels".
Change: Updated OS classification: "OS - Windows, Mac OS X, Android, iOS, etc (this is based on HTTP user agent strings and DHCP)".
Authentication Enhancements and New Dashboard Security Features
Change: Added "There is also a setting to increase the minimum password length to 12 characters instead of the default minimum of 8 characters."
Information for Cisco Meraki for Government users
Change: Added "Email alert notifications via SMS text message".
