Meraki Community
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 

About Durai

Re: Cisco Meraki VLAN creation Issue in MS 250

by in New Meraki Users
‎Apr 5 2023 5:03 AM
‎Apr 5 2023 5:03 AM
I will check it out and let you know.   Thanks for your swift response and making me correct.   let me try    Have a good day alemabrahao   ... View more

Re: Cisco Meraki VLAN creation Issue in MS 250

by in New Meraki Users
‎Apr 5 2023 4:41 AM
‎Apr 5 2023 4:41 AM
Hi Alemabrahao,   There is no ACL configured. But when i enable OSPF , i am able to ping the end devices which is connected within VLANs.       ... View more

Re: Cisco Meraki VLAN creation Issue in MS 250

by in New Meraki Users
‎Apr 5 2023 2:50 AM
‎Apr 5 2023 2:50 AM
Hi Alemabrahao,   Thank you for response and solution.   after changing the configuration as per your correction, Its working fine.   But i have one more query from this,   I am able to reach firewall from MS250 Also able to reach MS250 from switch.     But in MS250 switch,   i am not able to reach one VLAN gateway to Another VLAN.   Example:   192.168.10.1 to 192.168.12.1 is not communicating. 192.168.12.1 to 172.24.100.1 is not communicating.   Do we need to enable OSPF for all VLANs.   ... View more

Re: Cisco Meraki VLAN creation Issue in MS 250

by in New Meraki Users
‎Apr 4 2023 6:58 AM
‎Apr 4 2023 6:58 AM
Hi Alemabrahao,   Thank you for your response.   MS 250 Routing:    Default route  0.0.0.0/0  192.168.128.1  No Not preferred   Note : 192.168.128.1 is firewall IP address. (VLAN1 Which is in Firewall)   MX105   Default 0.0.0.0/0 192.168.128.5 always   192.168.128.5 is my switch IP address   Note : Switch is in Stack       ... View more

Cisco Meraki VLAN creation Issue in MS 250

by in New Meraki Users
‎Apr 4 2023 5:35 AM
‎Apr 4 2023 5:35 AM
  Hi All,   Good evening.   Recently we have bought MS250 Switch and MX105 firewall.   Here we need to keep all VLANs in MS250 instead of MX105.   In firewall we are keeping default VLAN 1 (192.168.128.0/24).   I have created 5 VLANs in MS250. But its not working.   VLANs are not able to reach firewall.   VLAN Details below.   192.168.10.0/24 Interface IP 192.168.10.1   192.168.12.0/29 Interface IP 192.168.12.1   192.168.12.8/29 Interface IP 192.168.128.9   172.24.100.0/24 Interface IP 172.24.100.1   * InterVLAN communication is not working.   But i have two end points in 192.168.12.5 1 / 92.168.128.6. I am able to access this end points from 192.168.12.1.   Do we need to enable OSPF for interVLAN communication?   Can some one help me to resolve this case since i am new to cisco meraki Environment.       ... View more
© 2024 Cisco Systems, Inc.