Meraki

twandrist · ‎Oct 26 2022

The only model we could get our hands on MR46's. We have MR56's backorder for 8 months we are still waiting on.

twandrist · ‎Oct 26 2022

Add them via inventory....DUH! Answered my own question. We all have these days right? :^)

twandrist · ‎Oct 26 2022

I seem to recall that once upon a time, one could add hardware/AP's to your cloud via order number. Then as you replace older MR34's with new models, deactivating the hardware and claim that license for the new hardware? We purchase a bunch of newer models that will replace old ones, but how do you get the new ones in your system? What am I missing?? Anyone run into this? TIA Tom

twandrist · ‎Oct 26 2022

After running a Fluke analyzer on the lines, it turned out to be patch cable related. Same manufacture of cables, one worked one didn't. And they had been working prior to this latest issue? Does POE+ tear up patch cables after a bit? IDK... but something to keep an eye on. Thanks for all your input.

twandrist · ‎Oct 6 2022

Cisco 3560x, POE+, dual power supplies. I have not ran a tester on the cables yet. The weird part is that they have worked fine for years up until recently? Same wire, same switches. One run is rather long, but one is 50ft and having the same issues. I am wondering if the Port Profile/Aggregation be the issue??? This was a relative new release if I recall correctly? The more I think about it, the more the timing of this coincides. We are just using the "default" port profile settings as we have no need, at this time for it. AGGREGATION Speed 100 Mbps Ethernet 1: Enabled Ethernet 2: Disabled

twandrist · ‎Oct 6 2022

Axl, did a factory reset on them already. They are fine for awhile then revert back to 100 Meg. I tried the newest Beta release on one of them 29.4. but that didn't seem to help either. I have replaced all the patch cables with new Cat6 cables, and that didn't help as well. I'm wondering if the Admin Console is miss-reporting the link speed??? They seem to work ok, but the console is telling me they are reverting back/ running at 100 meg?

twandrist · ‎Oct 6 2022

Axl, yes I have and had no issues with other POE+ devices. We have other AP's running on the same switches without issue? It just seems to be the MR53e units that this is happening to. If you reboot them, they might be fine for an hour, a day or so, next time I look, they are at 100 Meg. Thanks

twandrist · ‎Oct 5 2022

All are running on Cisco Switches, POE+ power injected on 1 Gig dedicated switch port. They keep reverting back to 100 Meg connection, or bouncing back and forth from 100 Meg to 1 Gig. This problem just seemed to have started as of late. We have changed nothing on the switch side, cabling has not changed, but yet the keep reporting that they are connected at 100 Meg, off a 1 GIG port? All have the latest version of firmware on them. Has anyone else seen this issue? TIA, Tom

Meraki

Community

About twandrist

twandrist

Community Record

Badges

Re: Adding replacement AP's and using existing license.

Re: Adding replacement AP's and using existing license.

Adding replacement AP's and using existing license.

Re: MR53E Access points reverting to 100 Meg switch port connection speed?

Re: MR53E Access points reverting to 100 Meg switch port connection speed?

Re: MR53E Access points reverting to 100 Meg switch port connection speed?

Re: MR53E Access points reverting to 100 Meg switch port connection speed?

MR53E Access points reverting to 100 Meg switch port connection speed?

Re: Adding replacement AP's and using existing license.

Re: Adding replacement AP's and using existing license.

Re: MR53E Access points reverting to 100 Meg switch port connection speed?