Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About GergelyK
GergelyK
Getting noticed
Member since May 8, 2018
May 13 2021
Community Record
25
Posts
14
Kudos
1
Solution
Badges
Jan 27 2021
3:08 AM
Hi, Thanks for the link, for some reason I did not found this when I was looking for it. It's sad to see that Meraki still hasn't implemented this (since 2018) while I would consider this as pretty basic requirement.
... View more
Jan 27 2021
3:06 AM
Hi, Sadly no, that is only alerts when the primary link goes down. In case the unused link goes down, it does not help.
... View more
Jan 26 2021
7:11 AM
1 Kudo
Hello Everyone, I would like to ask a bit of help to understand which Network-wide alert would be more suitable for our network. We are enabling Alerts trough Webhook. Our setup is that we have 2 Up-link, there is no load balancing between the 2, so only 1 has always an active AutoVPN. I would like to have a webhook trap even if the 2nd link goes down (which is inactive). As far as I can see in the Alert settings page there is no option for this, but I would like to double check if someone had similar problem before and how it was solved. My only idea would be to enable Active-Active AutoVPN and with that we could enable the VPN Alert which would send an alert via Webhook. But I wonder if we have a better solution than this. Thank you. 🙂
... View more
Sep 30 2020
7:59 AM
Hi Everyone, I've seen this question once already in the forum, but I'm hoping there is some kind of change in the meantime. (https://community.meraki.com/t5/Dashboard-Administration/Organization-wide-alerting/m-p/46118) The question would be the same, is there still no way to do an Organization wide alerting modification? I'm afraid that the answer is still not, but I never know... 🙂
... View more
May 14 2020
12:49 AM
1 Kudo
It's great to see that Meraki is also helping out. I'm doing Folding@Home in a different team, so I wouldn't change that at this time. 🙂
... View more
Feb 14 2020
12:59 AM
Hi Everyone, I would like to create an accurate bandwidth/utilization report from the appliance, however the current reporting is changing based on how I set up the date. I think the more broad view you are looking, the sample size also increasing, meaning in a 1 month look the utilization will not represent the truth. Does anyone has some kind of solution for this? Thank you, Greg
... View more
Oct 29 2019
9:40 AM
1 Kudo
Hi, I think the better option in this case to open a Meraki TAC case, again. I think you will get better answers from the TAC then from the forum in case of a possible backend issue. Probably they know already the solution, but needs to apply on a case to case basis.
... View more
Jul 12 2019
12:48 AM
2 Kudos
Hello All, The issue has been fixed. I just received the confirmation. 🙂 @Raj66 Thanks for the fast reply, and fix. 🙂
... View more
Jul 11 2019
5:38 AM
My biggest one, which wasn't a complete down is 1140% packet loss We are loosing from another circuit as well. 🙂
... View more
Jul 11 2019
3:49 AM
2 Kudos
Hi All, I've reported this out to Meraki TAC. They came back to me that they are checking this with the developer team. Cheers, Greg
... View more
Jul 11 2019
1:28 AM
Also I just noticed that the topic is in the wrong subject. I'm sorry about it. If an admin comes around here, can move this topic under "Dashboard & Administration"? 🙂 Thank you.
... View more
Jul 11 2019
1:10 AM
Well, that's good news I guess that it's not only me/us. Did you maybe know why is this happening, or should we get in touch with TAC?
... View more
Jul 11 2019
1:04 AM
1 Kudo
Hi All, Am I the only one who's Dashboard got changed? In one of my MX65 Uplink tab the Historical data part went from the normal dark and light blue to yellow and even lighter blue. I mean I don't really mind this change, but the legend has disappeared, and I'm pretty sure that a link can't drop more than 100% of packet. I have sites which showing packet loss peaks up to 200%. Yesterday this was perfectly normal for me. Is this a new visual bug? Cheers, Greg
... View more
May 21 2019
9:22 PM
Hello Everyone, Well this issue just dissipated. I mean the Meraki TAC did not see any issue, and they requested packet captures, but since after restart the problem went away I couldn't give them one. Provider said that they are up to date with their Firmware, so no luck there either. I guess if next time happens again I'll make a capture and we will see what happens 🙂
... View more
Apr 29 2019
4:48 PM
Thanks I'll check on it with the provider. I'll keep this one updated.
... View more
Apr 29 2019
4:34 PM
Hi Phil, Thanks for the fast reply. Nope they are 2 different NTU. One of them is usually a Technicolor and the other one is a Netgear. I haven't checked with the provider for firmware update on those devices. I'll check with them, as this is their device. Do you not thing that this can be an issue with the Meraki itself? We have similar sites with the same equipment which are running fine. Cheers, Greg
... View more
Apr 29 2019
4:20 PM
Hello Everyone, I'm writing to the forum as well, so maybe someone already see this kind of behaviour with their MX65. I'm working for a company who has normal xDSL internet lines all around the globe using Meraki VPN connections between them. We have 2 WAN interface activated (WAN1 and WAN2). Today our customer noticed that in one of the region they could see that the traffic failed over to WAN2 while the WAN1 was still active. I've checked the Traffic shaping and indeed the WAN1 is the Primary. It is visible that the WAN1 is up, but for some reason when checking the VPN status, the routing decesion was pointed to the WAN2 due to "Only uplink", while the WAN1 was still up. The VPN Registry said the following error message:"Disconnected. This security appliance is unable to connect to any VPN registries using outbound UDP port 9350." I've contacted our ISP to confirm what is happening on these circuits. They confirmed that there is no block on port level on these circuits. The interesting thing is that if you restart the MX65 on one of the affected site, after the reboot it will build up the connection without any issue. So I guess this will be some kind of bug. Does any of you encounter the same? I've already contacted Meraki TAC for further checking why is this happening as this was on multiple sites. But I'm wondering if this is something specific for us, or do you guys also see similar things? Cheers, Greg
... View more
Jan 4 2019
7:40 AM
Hi, I was actually coming back and asking for this as there is no EMEA session scheduled until this point. It might be missing because of the holiday period 🙂
... View more
Jan 4 2019
4:19 AM
Hi Ajit, I tough it will be announced in a public website as previously was done as well. Thanks for the heads up. 🙂 Cheers, Greg
... View more
Jan 4 2019
2:45 AM
Hello everyone, I'm searching for the CMNA on site training schedule for February, however I'm not able to find it anywhere. Is it not posted yet due to the holidays? If someone has a link and could give me that would be great. Thank you, Greg
... View more
Dec 5 2018
4:08 AM
1 Kudo
Hi Asfand, I think the Cellurar is only for failover. If you don't have any kind of WAN connected I'm not sure if it's works or not. I couldn't test it yet. Maybe @PhilipDAth has more knowledge if this could work or not. One thing how you can overcome this issue would be to buy a 2nd router and connect it before the Meraki. In this way you will have a portable antenna what you can place to the window for better coverage. Hopefully this helped. Cheers, Greg
... View more
Dec 5 2018
1:36 AM
I'm glad that I could help. If you think you this fully answered your question, please mark it as solved with the previous reply 🙂 Cheers, Greg
... View more
Dec 5 2018
1:18 AM
3 Kudos
HI Adster, if I understand you correctly your plan is to buy 2 x MX 65 and place one of them into the Main office and one in the new branch. If yes than it will be really easy. Once you connect them to the internet and created your organization in the dashboard and add both Mx-65 to your inventory and of course created the 2 sites after it's up to the races. Just don't forget to point them to each other so they will pull up the Ipsec tunnel between themselves. You don't need to connect Meraki MS series, you can use the legacy switches. I have a couple of branch offices that are using their old cisco switches and it is fully compatible. The only thing that you will not see them in your dashboard. One thing what you also can conciser with your client is maybe a dual internet connection. So you can minimize any kind of downtime in case of an issue with one of the ISP. MX65 has 2 WAN connection. I hope this information was sufficient. Cheers, Greg
... View more
May 8 2018
9:42 AM
Hello, Thank you, I've found that forum post, however it is hard for me to believe that such feature hasn't been implemented yet on the dashboard native alarm system.
... View more
May 8 2018
9:03 AM
1 Kudo
Hello All, I would like to know about the Alerting page on the Meraki dashboard. I have the following problem: We have around 100+ MX 65 devices. All of them have 2 kind of WAN connection. WAN 1 is always the Primary and WAN 2 is always the backup. There is no load balancing turned on. My issue is that when the WAN 2 connection is marked as "failed" we didn't receive any notification. Is there any solution by design in the Meraki dashboard already implemented, which is able to send us an email when the WAN 2 status changes? Thank you for the help.
... View more
My Accepted Solutions
| Subject | Views | Posted |
|---|---|---|
| 2651 | Dec 5 2018 1:18 AM |
My Top Kudoed Posts
| Subject | Kudos | Views |
|---|---|---|
| 3 | 2651 | |
| 2 | 8827 | |
| 2 | 9025 | |
| 1 | 1995 | |
| 1 | 35376 |
© 2024 Cisco Systems, Inc.
