Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
About Bassman
Community Record
7
Posts
1
Kudos
0
Solutions
Badges
Sep 7 2018
6:47 AM
Thanks for the response. No, that doesn't work either. I connected a PC running wire shark directly to the mirrored port for testing and can see that the port is indeed mirroring data, just the data capture does not work. This is for both and on-screen and to a file capture.
... View more
Aug 30 2018
8:06 AM
We have a MS425 Merkai switch and mirror traffic from 3 ports to port 14. Port 14 is then connected to security appliance to analyse for any security breaches etc. I would like to use the option within the Meraki console to run a packet capture on Port 14, but when I do there is no data captured. This must be something to do with the port being configured as a mirrored ports as it works on all other ports. When I do run a packet capture on Port 14, the only output that I get is:- --- Start Of Stream --- reading from file /tmp/click_pcap_dump, link-type EN10MB (Ethernet) --- End Of Stream --- I assume that this is normal and I cannot capture port traffic on the mirrored port by using the Meraki console? Thanks.
... View more
Jun 28 2018
8:05 AM
We have locked down most of our switch ports in our Organization by using 802.1x port security and Mac whitelists. Is there a way that I can automate a monthly report for our entire organization, which lists ports that have the access policy set to Open. I want to review this type of report on a monthly basis to ensure that a port has not been opened and left open by mistake.
... View more
Jun 4 2018
2:20 PM
Many thanks jdsilva 🙂 Yes, I am struggling to see how I can exclude the Guest Wireless traffic from using the Auto VPN. Maybe if the ADSL router has two ports then I can connect the second port directly to the Meraki core switch (vlan 999) and then bypass the MX84 althogether for guest wireless traffic? Port one of the ADSL router will remain connected to the MX and be used for VPN failover.
... View more
Jun 4 2018
9:27 AM
Hello, I am after some advice on how to configure a MX84 for our new office network. We have an MPLS connection to our WAN and a ADSL connection to the internet. What I would like to do is to have 3 cables from the MX84 – One to the MPLS router, One to the ADSL router and One to the Core switch. All local network clients will be connected to the Core switch. I have configured a Site to Site VPN at our main office. (192.168.49.0/29) What I would like is for all traffic from our core switch on vlan’s 100(Corp LAN), 200 (Corp Wireless), and 5 (Management) to use the MPLS as the default route, but then to use the ADSL (site to site VPN) connection if the MPLS goes offline. However, traffic from the core switch on vlan 999 must ALWAYS go via the ADSL for Internet access and NEVER use the MPLS or Site to Site VPN. Proposed vLANs and Private IP's for the local network are:- (Corp LAN) – vLAN 100 - 10.49.64.0/19 (Corporate Wireless) vLAN 200 - 10.149.64.0/19 (Management) vLAN 5 - 10.49.96.0/19 (Guest Wireless) vLAN 999 - IP address from ADSL router. DHCP will be configured on the Meraki Switch to allocate IP's to the corporate LAN clients and the Corporate Wireless devices. Guest Wireless devices will get IP from the ADSL router. Is what I am asking possible and can anyone advise on the configuration settings that I need to make on the MX84 and help advise on which ports to use on the MX84 to connect to the following devices :- A - Meraki Core Network Switch B - MPLS Router C - ADSL Router Thanks in advance.
... View more
© 2024 Cisco Systems, Inc.
