The Meraki Community
Register or Sign in
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Show  only  | Search instead for 
Did you mean: 
  • About SENSEi-James
SENSEi-James

SENSEi-James

Just browsing

Member since Mar 25, 2022

‎03-30-2022

Community Record

6
Posts
0
Kudos
0
Solutions

Badges

First 5 Posts View All
Latest Contributions by SENSEi-James
  • Topics SENSEi-James has Participated In
  • Latest Contributions by SENSEi-James

Re: Scanning API POST interval

by SENSEi-James in Wireless LAN
‎03-30-2022 02:08 AM
‎03-30-2022 02:08 AM
Thanks @PhilipDAth    It's the interval between posts from the scanning APIs that I'm trying to find if there's a maximum length of, irrespective of how any particular device behaves.   It's back up to about 7 to 11 minutes this morning.  Overnight I noticed it was occasionally down to just over a minute.   Can anyone from Cisco comment if there's a maximum possible duration for the post interval?  Will something timeout if the interval gets too long?   This is to help me make some design decisions for an analytics service.   ... View more

Scanning API POST interval

by SENSEi-James in Wireless LAN
‎03-29-2022 07:51 AM
‎03-29-2022 07:51 AM
According to the docs for both V2 and V3 scanning APIs   'One JSON POST per access point, per minute per, type (WiFi/BLE)'   but with these disclaimers:   V2: 'Note: Meraki cannot provide a guaranteed interval, as it can depend on a number of factors, including quantity of access points in the network, and the response time (latency) of the customer receiver. Typical POST intervals range from 1-2 minute intervals, but are not guaranteed.'   V3: 'Note: Meraki cannot provide a guaranteed interval, as it can depend on a number of factors, including quantity of access points in the network, and the response time (latency) of the customer receiver. Typical POST intervals range from 2-3 minute intervals, but are not guaranteed.'   This morning on V2, I was seeing intervals up to 11 minutes.  At the moment the intervals are back down to around 4 minutes.  V3 is still not sending anything at all at the moment.   Is there a maximum interval that I can safely rely upon?   I see there's a variety of reasons for these increased intervals.  Is it because those reasons are causing increased load on the APs, or increased load on the Meraki cloud services, or something else?   Thanks 🙂 James ... View more

Re: Nothing being pushed from scanning API v3

by SENSEi-James in Wireless LAN
‎03-25-2022 08:46 AM
‎03-25-2022 08:46 AM
Sorry, didn't answer your question about how many APs.  There are 8. I have opened a support case. I have DM'd a serial number ... View more

Re: Nothing being pushed from scanning API v3

by SENSEi-James in Wireless LAN
‎03-25-2022 08:21 AM
‎03-25-2022 08:21 AM
One month ago, I was running with ONE AP and collecting lots of information (but no trilaterated locations) with ONE AP   According to your own documentation, I should still be receiving some data:   - START QUOTE-   What will happen if I enable V3, but some physical locations don’t have at least three compatible APs? In scenarios where the Scanning API V3 does not have at least 3 data points, no location information will be generated in the API output for a given wireless client. The API will provide the nearest AP MAC address based on the RSSI in the output. This can be used to get a rough estimate of the location of the wireless client device on the floor plan, but it is recommended to deploy at least three APs at any physical location that is upgrading to Scanning API V3   -END QUOTE-   ... View more

Re: Nothing being pushed from scanning API v3

by SENSEi-James in Wireless LAN
‎03-25-2022 08:06 AM
‎03-25-2022 08:06 AM
Firmware version info shows:   Up to date Current version: MR 28.5 ... View more

Nothing being pushed from scanning API v3

by SENSEi-James in Wireless LAN
‎03-25-2022 05:16 AM
‎03-25-2022 05:16 AM
Hi, One month ago I developed a service to receive data pushed from the scanning API v3.  This was working fine and plenty of data was coming in. The APs were boxed up and shipped to a customer.  They were installed and turned on yesterday.  Nothing is being pushed from the scanning API v3.  If I change it to v2, loads of 'DevicesSeen' data gets pushed to me, but that's not what I've developed my service to work with.   Is there a problem with the scanning API v3 at the moment, or am I missing something obvious?   Many thanks 🙂 James ... View more
Powered by Khoros
custom.footer.
  • Community Guidelines
  • Cisco Privacy
  • Khoros Privacy
  • Privacy Settings
  • Terms of Use
© 2023 Meraki